LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 2053 (Driver Information System) >> Warning Chime >> Key Warning Chime Does Not Operate
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Key Warning Chime Does Not Operate

WARNING: This page is about a different car, the 2007 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUSE 

    Check if the key switch 15A fuse [No. 19, located in the fuse block (J/B)] is blown. Refer to "WIRING DIAGRAM - CHIME ".

    Is the fuse blown? 

    YES: Replace the fuse. Be sure to repair the cause of malfunction before installing new fuse.

    No: GO TO 2.

  2. CHECK WARNING CHIME OPERATION 

    With key removed from the ignition and the front door LH open, turn the lighting switch to 1st or 2nd position.

    Does warning chime sound? 

    Yes: GO TO 3.

    No: GO to "ALL WARNING CHIMES DO NOT OPERATE " or "KEY WARNING CHIME AND LIGHT WARNING CHIME DO NOT OPERATE (SEAT BELT WARNING CHIME DOES OPERATE) ".

  3. CHECK BCM INPUT SIGNAL 

    With CONSULT-II 

    With "DATA MONITOR" of "BUZZER", confirm "KEY ON SW" changes when the key is inserted/removed from the ignition key cylinder.

    When key is inserted in ignition key cylinder : KEY ON SW ON 

    When key is removed from ignition key cylinder : KEY ON SW OFF 

    Fig 1: CONSULT-II Display - Data Monitor
    G04903791Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    Check voltage between BCM harness connector M18 terminal 37 and ground.

    VOLTAGE CHART

    Terminals Condition Voltage (V)
    (+) (-)
    Connector Terminal
    M18 37 Ground Key is inserted Battery voltage
    Key is removed 0
    Fig 2: Checking Voltage Between BCM Connector M18 Terminal 37 And Ground
    G04903792Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace the BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".

    NG: GO TO 4.

  4. CHECK KEY SWITCH 
    1. Disconnect key switch connector.
    2. Check continuity between key switch terminals 1 and 2.
      CONTINUITY REFERENCE CHART

      Terminals Condition Continuity
      1 2 Key is inserted Yes
      Key is removed No
      Fig 3: Checking Continuity Between Key Switch Terminals 1 And 2
      G04908731Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 5.

    NG: Replace the key switch.

  5. CHECK KEY SWITCH CIRCUIT 
    1. Disconnect BCM connector M18.
    2. Check continuity between BCM harness connector M18 terminal 37 and key switch harness connector M27 terminal 2.

      Continuity should exist. 

    3. Check continuity between BCM harness connector M18 terminal 37 and ground.

      Continuity should not exist. 

    OK or NG 

    OK: GO TO 6.

    NG: Repair harness or connector.

    Fig 4: Checking Continuity Between BCM Harness Connector M18 Terminal 37 And Key Switch Harness Connector M27 Terminal 2, And Between BCM Harness Connector M18 Terminal 37 And Ground
    G04908732Courtesy of NISSAN MOTOR CO., U.S.A.
  6. CHECK KEY SWITCH POWER SUPPLY CIRCUIT 

    Check voltage between key switch harness connector M27 terminal 1 and ground.

    Battery voltage should exist. 

    OK or NG 

    OK: Replace the BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".

    NG: Check harness for open between key switch and fuse.

    Fig 5: Checking Voltage Between Key Switch Harness Connector M27 Terminal 1 And Ground
    G04908733Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals