Front Power Window RH Circuit Check (Main Power Window and Door Lock/Unlock Switch Operation)

1. Turn ignition switch OFF.
2. Disconnect front power window motor RH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor RH connector and ground.
   CONNECTOR TERMINAL VOLTAGE SPECIFICATION
   
   

   Connector	Terminals		Condition	Voltage (V) (Approx.)
   	(+)	(-)
   D105	1	Ground	UP	0
   			DOWN	Battery voltage
   	2		UP	Battery voltage
   			DOWN	0

   Fig 1: Checking Voltage Between Front Power Window Motor RH Connector And Ground

   

OK or NG 

OK: Replace front power window motor RH. Refer to "REGULATOR ASSEMBLY ".

NG: GO TO 2.

1. Turn ignition switch OFF.
2. Disconnect front power window motor RH and power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and front power window motor RH connector D105 (B) terminals 1, 2.

   7 - 1 : Continuity should exist. 

   6 - 2 : Continuity should exist. 

4. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and ground.

   6 - Ground : Continuity should not exist. 

   7 - Ground : Continuity should not exist. 

   Fig 2: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Connector D104 Terminals 6, 7 And Ground

   

OK or NG 

OK: GO TO 3.

: Repair or replace harness.

1. Turn ignition switch OFF.
2. Check continuity between power window and door lock/unlock switch RH terminals.
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   Power window and door lock/unlock switch	Terminals		Continuity
   	6	11	Yes
   	7	12	Yes

   Fig 3: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Terminals

   

OK or NG 

OK: GO TO 4.

NG: Replace power window and door lock/unlock switch RH. Refer to "FRONT DOOR ".

1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch and power window connector (A) and door lock/unlock switch RH connector (B).
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		B		Continuity
   Connector	Terminal	Connector	Terminal
   D5	2	D104	11	Yes
   	3		12	Yes

3. Check continuity between main power window and door lock/unlock switch connector (A) and ground.
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		Ground	Continuity
   Connector	Terminal
   D5	2		No
   	3		No

   Fig 4: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Connector And Ground

   

OK or NG 

OK: GO TO 5.

NG: Repair or replace harness.

1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch connector and ground.
   CONNECTOR TERMINAL VOLTAGE SPECIFICATION
   
   

   Connector	Terminals		Condition	Voltage (V) (Approx.)
   	(+)	(-)
   D5	3	Ground	UP	Battery voltage
   			DOWN	0
   	2		UP	0
   			DOWN	Battery voltage

   Fig 5: Checking Voltage Between Main Power Window And Door Lock/ Unlock Switch And Ground

   

OK or NG 

OK: Repair or replace harness.

NG: Replace main power window and door lock/unlock switch. Refer to "FRONT DOOR ".