LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2012 >> Sentra SE-R >> Repair and Diagnosis >> Brakes >> Traction Control >> Brake Control System (VDC/TCS/Abs) >> Service Information >> Trouble Diagnosis >> Control Unit Input/Output Signal Standard >> Reference Value From Consult
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Reference Value From Consult

CAUTION: The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.
Monitor item Display content Data monitor
NOTE: Error inspection checklist
Condition Reference value in normal operation
FR LH SENSOR
FR RH SENSOR
RR LH SENSOR
RR RH SENSOR
Wheel speed Vehicle stopped 0 [km/h (mph)] WHEEL SENSOR SYSTEM INSPECTION 
Vehicle running ((1)) Almost in accordance with speedometer display (within ±10%)
FR RH IN SOL
FR RH OUT SOL
FR LH IN SOL
FR LH OUT SOL
RR RH IN SOL
RR RH OUT SOL
RR LH IN SOL
RR LH OUT SOL
Solenoid valve operation Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (in fail-safe mode). On SOLENOID AND VDC CHANGE-OVER VALVE SYSTEM INSPECTION 
When actuator (solenoid) is not active and actuator relay is active (ignition switch ON). Off
STOP LAMP SW Brake pedal operation Brake pedal depressed On STOP LAMP SWITCH SYSTEM INSPECTION 
Brake pedal released Off
MOTOR RELAY Operation status of motor and motor relay Ignition switch ON or engine running (ABS not operated) Off ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION 
Ignition switch ON or engine running (ABS operated) On
ACTUATOR RLY Actuator relay operation status Vehicle stopped (Ignition switch ON) Off
Vehicle stopped (Engine running) On
ABS WARN LAMP ABS warning lamp ON condition ((2)) ABS warning lamp ON On ABS WARNING LAMP DOES NOT COME ON WHEN IGNITION SWITCH IS TURNED ON 
ABS warning lamp OFF Off
OFF LAMP VDC OFF indicator lamp status ((2)) When VDC OFF indicator lamp is ON On CAN COMMUNICATION SYSTEM INSPECTION 
When VDC OFF indicator lamp is OFF Off
OFF SW VDC OFF switch ON/OFF status VDC OFF switch ON (When VDC OFF indicator lamp is ON) On COMPONENT INSPECTION 
VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) Off
SLIP LAMP SLIP indicator lamp status ((2)) When SLIP indicator lamp is ON On CAN COMMUNICATION SYSTEM INSPECTION 
When SLIP indicator lamp is OFF Off
BATTERY VOLT Battery voltage supplied to ABS actuator and electric unit (control unit) Ignition switch ON 10 to 16V ABS/TCS/VDC CONTROL UNIT POWER AND GROUND SYSTEMS INSPECTION 
GEAR Manual mode gear position determined by TCM Ignition switch ON 1
2
3
4
5
6
-
YAW RATE SEN Yaw rate detected by yaw rate/side G sensor Vehicle stopped Approx. 0 d/s YAW RATE/SIDE/DECEL G SENSOR SYSTEM INSPECTION 
Vehicle turning -75 to 75 d/s
ACCEL POS SIG Open/close condition of throttle valve (linked with accelerator pedal) Accelerator pedal not depressed (ignition switch is ON) 0% CAN COMMUNICATION SYSTEM INSPECTION 
Depress accelerator pedal (ignition switch is ON) 0 to 100%
SIDE G-SENSOR Transverse G detected by side G-sensor Vehicle stopped Approx. 0 m/s2 YAW RATE/SIDE/DECEL G SENSOR SYSTEM INSPECTION 
Vehicle turning right negative value (m/s2 )
Vehicle turning left positive value (m/s2 )
STR ANGLE SIG Steering angle detected by steering angle sensor Straight-ahead Approx. 0° STEERING ANGLE SENSOR SYSTEM INSPECTION 
Steering wheel turned -720 to 720°
PRESS SENSOR Brake fluid pressure detected by pressure sensor With ignition switch ON and brake pedal released Approx. 0 bar PRESSURE SENSOR SYSTEM INSPECTION 
With ignition switch ON and brake pedal depressed -40 to 300 bar
EBD SIGNAL EBD operation EBD is active On -
EBD is inactive Off
ABS SIGNAL ABS operation ABS is active On -
ABS is inactive Off
TCS SIGNAL TCS operation TCS is active On -
TCS is inactive Off
VDC SIGNAL VDC operation VDC is active On -
VDC is inactive Off
EBD FAIL SIG EBD fail-safe signal In EBD fail safe mode On -
EBD is normal Off
ABS FAIL SIG ABS fail-safe signal In ABS fail safe mode On -
ABS is normal Off
TCS FAIL SIG TCS fail-safe signal In TCS fail safe mode On -
TCS is normal Off
VDC FAIL SIG VDC fail-safe signal In VDC fail safe mode On -
VDC is normal Off
CRANKING SIG Crank operation Crank is active On -
Crank is inactive Off
FLUID LEV SW Status of brake fluid level switch When brake fluid level switch ON On BRAKE FLUID LEVEL SWITCH SYSTEM INSPECTION 
When brake fluid level switch OFF Off
PARK BRAKE SW Status of parking brake switch Parking brake switch is active On COMPONENT INSPECTION 
Parking brake switch is inactive Off
USV[FL-RR]
USV[FR-RL]
HSV[FL-RR]
HSV[FR-RL]
VDC switch-over valve status When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT) or actuator relay is inactive (when in fail-safe mode). On SOLENOID AND VDC CHANGE-OVER VALVE SYSTEM INSPECTION 
When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON). Off
V/R OUPUT Solenoid valve relay activated When solenoid valve relay is active (ignition switch OFF) On
When solenoid valve relay is not active (in fail-safe mode) Off
M/R OUTPUT Actuator motor and motor relay activated When actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT) On ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION 
When actuator motor and motor relay are inactive Off
ENGINE RPM With engine running With engine stopped 0 rpm ENGINE SYSTEM INSPECTION 
Engine running Almost in accordance with tachometer display
(1) Confirm tire pressure is normal.
(2) On and Off timing for warning lamp and indicator lamp.