LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2012 >> Sentra SE-R >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Introduction (Qr25DE) >> Service Information >> Trouble Diagnosis - Specification Value >> Diagnosis Procedure >> Detailed Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Detailed Procedure

  1. CHECK "A/F ALPHA-B1", "A/F ALAPHA-B2"
    1. Start engine.
    2. Confirm that the testing conditions are met. Refer to "TESTING CONDITION ".
    3. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.
    NOTE: Check "A/F ALPHA-B1", "A/F ALPHA-B2" for approximately 1 minute because they may fluctuate. It is NG if the indication is out of the SP value even a little.

    OK or NG 

    OK: GO TO  17.

    NG (Less than the SP value) >> GO TO 2.

    NG (More than the SP value) >> GO TO  3.

  2. CHECK "B/FUEL SCHDL"

    Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: GO TO 4.

    NG (More than the SP value) >> GO TO  19.

  3. CHECK "B/FUEL SCHDL"

    Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: GO TO  6.

    NG (More than the SP value) >> GO TO  6.

    NG (Less than the SP value) >> GO TO  25.

  4. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Stop the engine.
    2. Disconnect PCV hose, and then plug it.
    3. Start engine.
    4. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: GO TO 5.

    NG: GO TO  6.

  5. CHANGE ENGINE OIL
    1. Stop the engine.
    2. Change engine oil. Refer to , "ENGINE OIL: CHANGING ENGINE OIL ".
    NOTE: This symptom may occur when a large amount of gasoline is mixed with engine oil because of driving conditions (such as when engine oil temperature does not rise enough since a journey distance is too short during winter). The symptom will not be detected after changing engine oil or changing driving condition.

    INSPECTION END 

  6. CHECK FUEL PRESSURE

    Check fuel pressure. (Refer to "FUEL PRESSURE CHECK ".)

    OK or NG 

    OK: GO TO  9.

    NG (Fuel pressure is too high)>>Replace fuel pressure regulator, refer to , "REMOVAL AND INSTALLATION " and "PRECAUTION ". GO TO  8.

    NG (Fuel pressure is too low) >> GO TO 7.

  7. DETECT MALFUNCTIONING PART
    1. Check the following.
      • Clogged and bent fuel hose and fuel tube
      • Clogged fuel filter
      • Fuel pump and its circuit (Refer to FUEL PUMP .)
    2. If NG, repair or replace the malfunctioning part. (Refer to "FUEL PRESSURE CHECK ".)

    If OK, replace fuel pressure regulator. Refer to , "REMOVAL AND INSTALLATION " and "PRECAUTION ".

    GO TO 8.

  8. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Start engine.
    2. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO 9.

  9. PERFORM POWER BALANCE TEST
    1. Perform "POWER BALANCE" in "ACTIVE TEST" mode.
    2. Check that the each cylinder produces a momentary engine speed drop.

    OK or NG 

    OK: GO TO  12.

    NG: GO TO 10.

  10. DETECT MALFUNCTIONING PART
    1. Check the following.
    2. If NG, repair or replace the malfunctioning part.

    If OK, replace fuel injector. (It may be caused by leakage from fuel injector or clogging.) Refer to , "REMOVAL AND INSTALLATION ".

    GO TO 11.

  11. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Start engine.
    2. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO 12.

  12. CHECK A/F SENSOR 1 FUNCTION

    Perform all DTC Confirmation Procedure related with A/F sensor 1.

    OK or NG 

    OK: GO TO  15.

    NG: GO TO 13.

  13. CHECK A/F SENSOR 1 CIRCUIT

    Perform Diagnostic Procedure according to corresponding DTC.

    GO TO 14.

  14. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Start engine.
    2. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO 15.

  15. DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR
    1. Stop the engine.
    2. Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.

    GO TO 16.

  16. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Start engine.
    2. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: Detect malfunctioning part according to "SYMPTOM MATRIX CHART ".

  17. CHECK "B/FUEL SCHDL"

    Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG (More than the SP value) >> GO TO 18.

    NG (Less than the SP value) >> GO TO  25.

  18. DETECT MALFUNCTIONING PART
    1. Check for the cause of large engine friction. Refer to the following.
      • Engine oil level is too high
      • Engine oil viscosity
      • Belt tension of alternator, A/C compressor, etc. is excessive
      • Noise from engine
      • Noise from transmission, etc.
    2. Check for the cause of insufficient combustion. Refer to the following.
    • Valve clearance malfunction
    • Intake valve timing control function malfunction
    • Camshaft sprocket installation malfunction, etc.

    Repair or replace malfunctioning part, and then GO TO  30.

  19. CHECK INTAKE SYSTEM

    Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

    • Crushed air ducts
    • Malfunctioning seal of air cleaner element
    • Uneven dirt of air cleaner element
    • Improper specification of intake air system

    OK or NG 

    OK: GO TO  21.

    NG: Repair or replace malfunctioning part, and then GO TO 20.

  20. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2" AND "B/FUEL SCHDL"

    Select "A/F ALPHA-B1", "A/F ALPHA-B1" and "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG ("B/FUEL SCHDL" is more, "A/F ALPHA-B1", "A/F ALPHA-B2" is less than the SP value) >> GO TO 21.

  21. DISCONNECT AND RECONNECT MASS AIR FLOW SENSOR HARNESS CONNECTOR
    1. Stop the engine.
    2. Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and then reconnect it again.

    GO TO 22.

  22. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2"
    1. Start engine.
    2. Select "A/F ALPHA-B1", "A/F ALPHA-B2" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK >>

    1. Detect malfunctioning part of mass air flow sensor circuit and repair it. Refer to DTC P0101 MAF SENSOR .
    2. GO TO  29.

    NG: GO TO 23.

  23. CHECK "MAS A/F SE-B1"

    Select "MAS A/F SE-B1" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: GO TO 24.

    NG (More than the SP value)>>Replace mass air flow sensor, refer to REMOVAL AND INSTALLATION , and then GO TO  29.

  24. REPLACE ECM
    1. Replace ECM.
    2. Perform initialization of NVIS(NATS) system and registration of all NVIS(NATS) ignition key IDs.

      Refer to , "ECM RE-COMMUNICATING FUNCTION ".

    3. Perform "VIN REGISTRATION ".
    4. Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING ".
    5. Perform "THROTTLE VALVE CLOSED POSITION LEARNING ".
    6. Perform "IDLE AIR VOLUME LEARNING ".

    GO TO  29.

  25. CHECK INTAKE SYSTEM

    Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

    • Crushed air ducts
    • Malfunctioning seal of air cleaner element
    • Uneven dirt of air cleaner element
    • Improper specification of intake air system

    OK or NG 

    OK: GO TO  27.

    NG: Repair or replace malfunctioning part, and then GO TO 26.

  26. CHECK "B/FUEL SCHDL"

    Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG (Less than the SP value) >> GO TO 27.

  27. CHECK "MAS A/F SE-B1"

    Select "MAS A/F SE-B1" in "SPEC" of "DATA MONITOR" mode, and check that the indication is within the SP value.

    OK or NG 

    OK: GO TO 28.

    NG (Less than the SP value)>>Replace mass air flow sensor, refer to , "REMOVAL AND INSTALLATION ", and then GO TO  30.

  28. CHECK INTAKE SYSTEM

    Check for the cause of air leak after the mass air flow sensor. Refer to the following.

    • Disconnection, looseness, and cracks in air duct
    • Looseness of oil filler cap
    • Disconnection of oil level gauge
    • Open stuck, breakage, hose disconnection, or cracks of PCV valve
    • Disconnection or cracks of EVAP purge hose, open stuck of EVAP canister purge volume control solenoid valve
    • Malfunctioning seal of rocker cover gasket
    • Disconnection, looseness, or cracks of hoses, such as vacuum hose, connecting to intake air system parts
    • Malfunctioning seal of intake air system, etc.

    GO TO  30.

  29. CHECK "A/F ALPHA-B1", "A/F ALPHA-B2" AND "B/FUEL SCHDL"

    Select "A/F ALPHA-B1", "A/F ALPHA-B2" and "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and check that the each indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: Detect malfunctioning part according to "SYMPTOM MATRIX CHART ".

  30. CHECK "B/FUEL SCHDL"

    Select "B/FUEL SCHDL" in "SPEC" of "DATA MONITOR" mode, and then check that the indication is within the SP value.

    OK or NG 

    OK: INSPECTION END 

    NG: Detect malfunctioning part according to "SYMPTOM MATRIX CHART ".

scientia non olet · About LEMON Manuals