LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2012 >> Versa SV >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Component Testing (Sedan) >> Ignition Signal >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-I
    1. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
    2. Check the voltage between ECM harness connector and ground.
      ECM Voltage
      Connector Terminal
      + -
      E16 105 108 Battery voltage

      Is the inspection result normal? 

      YES: GO TO 2.

      NO: Go to "DIAGNOSIS PROCEDURE ".

  2. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II
    1. Turn ignition switch OFF.
    2. Disconnect condenser harness connector.
    3. Turn ignition switch ON.
    4. Check the voltage between condenser harness connector and ground.
      Condenser Ground Voltage
      Connector Terminal
      F26 1 Ground Battery voltage

      Is the inspection result normal? 

      YES: GO TO  5.

      NO: GO TO 3.

  3. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-III
    1. Turn ignition switch OFF.
    2. Disconnect IPDM E/R harness connector F42.
    3. Check the continuity between IPDM E/R harness connector and condenser harness connector.
      IPDM E/R Condenser Continuity
      Connector Terminal Connector Terminal
      F42 34 F26 1 Existed
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  11.

      NO: GO TO 4.

  4. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness for open or short between IPDM E/R and condenser

    : Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Check the continuity between condenser harness connector and ground.
      Condenser Ground Continuity
      Connector Terminal
      F26 2 Ground Existed
    3. Also check harness for short to power.

      Is the inspection result normal? 

      YES: GO TO 6.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  6. CHECK CONDENSER

    Refer to "COMPONENT INSPECTION (CONDENSER) "

    Is the inspection result normal? 

    YES: GO TO 7.

    NO: Replace condenser.

  7. CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IV
    1. Reconnect all harness connectors disconnected.
    2. Disconnect ignition coil harness connector.
    3. Turn ignition switch ON.
    4. Check the voltage between ignition coil harness connector and ground.
      Ignition coil Ground Voltage
      Cylinder Connector Terminal
      1 F34 3 Ground Battery voltage
      2 F35 3
      3 F36 3
      4 F37 3

      Is the inspection result normal? 

      YES: GO TO 8.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  8. CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Check the continuity between ignition coil harness connector and ground.
      Ignition coil Ground Continuity
      Cylinder Connector Terminal
      1 F34 2 Ground Existed
      2 F35 2
      3 F36 2
      4 F37 2
    3. Also check harness for short to power.

      Is the inspection result normal? 

      YES: GO TO 9.

      NO: Repair open circuit or short to power in harness or connectors.

  9. CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Disconnect ECM harness connector.
    2. Check the continuity between ECM harness connector and ignition coil harness connector.
      Ignition coil ECM Continuity
      Cylinder Connector Terminal Connector Terminal
      1 F34 1 F10 17 Existed
      2 F35 1 18
      3 F36 1 22
      4 F37 1 21
    3. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 10.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  10. CHECK IGNITION COIL WITH POWER TRANSISTOR

    Refer to "COMPONENT INSPECTION (IGNITION COIL WITH POWER TRANSISTOR) ".

    Is the inspection result normal? 

    YES: GO TO 11.

    NO: Replace malfunctioning ignition coil with power transistor. Refer to "REMOVAL AND INSTALLATION ".

  11. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals