Values On The Diagnosis Tool

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
Numerical values in the following table are reference values.
These values are input/output values that ECM receives/transmits and may differ from actual operations.

Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the data monitor. This occurs because the timing light shows a value calculated by ECM according to signals received from the cam shaft position sensor and other sensors related to ignition timing.

For outlines of following items, refer to "CONSULT FUNCTION ".

Monitor Item

Condition

Values/Status

ENG SPEED

Run engine and compare CONSULT value with the tachometer indication.

Almost the same speed as the tachometer indication.

MAS A/F SE-B1

See "DIAGNOSIS PROCEDURE ".

B/FUEL SCHDL

See "DIAGNOSIS PROCEDURE ".

A/F ALPHA-B1

See "DIAGNOSIS PROCEDURE ".

COOLANT TEMP/S

Engine: After warming up

More than 70°C (158°F)

A/F SEN1 (B1)

Engine: After warming up

Maintaining engine speed at 2, 000 rpm

Fluctuates around 2.2 V

HO2S2 (B1)

Revving engine from idle up to 3, 000 rpm quickly after the following conditions are met.
- Engine: After warming up
- After keeping engine speed between 3, 500 and 4, 000 rpm for 1 minute and at idle for 1 minute under no load

0 - 0.3 V ←→ Approx. 0.6 - 1.0 V

HO2S2 MNTR(B1)

Revving engine from idle up to 3, 000 rpm quickly after the following conditions are met.
- Engine: After warming up
- After keeping engine speed between 3, 500 and 4, 000 rpm for 1 minute and at idle for 1 minute under no load

LEAN ←→ RICH

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as speedometer indication

BATTERY VOLT

Ignition switch: ON (Engine stopped)

11 - 14 V

ACCEL SEN 1

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.5 - 1.0 V

Accelerator pedal: Fully depressed

4.2 - 4.8 V

ACCEL SEN 2⁽¹⁾

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.5 - 1.0 V

Accelerator pedal: Fully depressed

4.2 - 4.8 V

TP SEN 1-B1

Ignition switch: ON (Engine stopped)
Selector lever: D (CVT)
Shifter lever: 1st (M/T)

Accelerator pedal: Fully released

More than 0.36 V

Accelerator pedal: Fully depressed

Less than 4.75 V

TP SEN 2-B1⁽¹⁾

Ignition switch: ON (Engine stopped)
Selector lever: D
Shifter lever: 1st (M/T)

Accelerator pedal: Fully released

More than 0.36 V

Accelerator pedal: Fully depressed

Less than 4.75 V

FUEL T/TMP SE

Ignition switch: ON

Indicates fuel tank temperature

EVAP SYS PRES

Ignition switch: ON

Approx. 1.8 - 4.8 V

FUEL LEVEL SE

Ignition switch: ON

Depending on fuel level of fuel tank

START SIGNAL

Ignition switch ON → START → ON (start switch is released)

Off → On → Off

CLSD THL POS

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

Accelerator pedal: Slightly depressed

Off

AIR COND SIG

Engine: After warming up, idle the engine

Air conditioner switch: OFF

Off

Air conditioner switch: ON (A/C compressor operates)

PW/ST SIGNAL

Engine: After warming up, idle the engine

Steering wheel: Not being turned

Off

Steering wheel: Being turned

LOAD SIGNAL

Ignition switch: ON

Rear window defogger switch: ON and/or Lighting switch: 2nd position

Rear window defogger switch and lighting switch: OFF

Off

IGNITION SW

Ignition switch: ON → OFF → ON

On → Off → On

HEATER FAN SW

Engine: After warming up, idle the engine

Heater fan switch: ON

Heater fan switch: OFF

Off

BRAKE SW

Ignition switch: ON

Brake pedal: Fully released

Off

Brake pedal: Slightly depressed

INJ PULSE-B1

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

2.0 - 3.0 msec

2, 000 rpm

1.9 - 2.9 msec

IGN TIMING

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

3° - 13° BTDC

2, 000 rpm

35° - 55° BTDC

CAL/LD VALUE

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

10% - 35%

2, 500 rpm

10% - 35%

MASS AIRFLOW

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

Approx. 2.9 g/s

2, 500 rpm

Approx. 5.5 g/s

PURG VOL C/V

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle
(Accelerator pedal: Not depressed even slightly, after engine starting.)

2, 000 rpm

0% - 90%

INT/V TIM(B1)

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

-5°-- 5° CA

2, 000 rpm

Approx. 0° - 20° CA

EXH/V TIM B1

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

-5° - 5° CA

2, 000 rpm

Approx. 0° - 40° CA

INT/V SOL (B1)

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

0%-- 2%

2, 000 rpm

Approx. 0%-- 90%

SWRL CONT S/V

Ignition switch: ON
Engine coolant temperature: Between 0°C (32°F) and 45°C (113°F)

Accelerator pedal: Fully released

Accelerator pedal: Fully depressed

Off

VIAS S/V-1

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

When revving engine up to 5, 250 rpm quickly and release the accelerator pedal.

Off → On → Off

AIR COND RLY

Engine: After warming up, idle the engine

Air conditioner switch: OFF

Off

Air conditioner switch: ON (Compressor operates)

FUEL PUMP RLY

For 1 second after turning ignition switch: ON
Engine running or cranking

Except above

Off

VENT CONT/V

Ignition switch: ON

Off

THRTL RELAY

Ignition switch: ON

COOLING FAN

Engine: After warming up, idle the engine
Air conditioner switch: OFF

Engine coolant temperature is 97°C (207°F) or less

Off

Engine coolant temperature between 98°C (208°F) and 99°C (210°F) or more

Low

Engine coolant temperature between 100°C (212°F) or more

Engine: After warming up, idle the engine
Air conditioner switch: ON
Refrigerant pressure is less than 1, 280 kPa (12.80 bar, 13.05 kg/cm² , 185.6 psi)

Engine coolant temperature is 97°C (207°F) or less

Low

Engine coolant temperature between 98°C (208°F) and 99°C (210°F) or more

Low

Engine coolant temperature between 100°C (212°F) or more

HO2S2 HTR (B1)

Engine speed: Below 3, 600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3, 500 and 4, 000 rpm for 1 minute and at idle for 1 minute under no load

Engine speed: Above 3, 600 rpm

Off

ALT DUTY SIG

Power generation voltage variable control: Operating

Power generation voltage variable control: Not operating

Off

I/P PULLY SPD

Vehicle speed: More than 20 km/h (12 MPH)

Almost the same speed as the tachometer indication

VEHICLE SPEED

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

IDL A/V LEARN

Engine: running

Idle air volume learning has not been performed yet.

YET

Idle air volume learning has already been performed successfully.

CMPLT

TRVL AFTER MIL

Ignition switch: ON

Vehicle has traveled after MIL has turned ON.

0 - 65, 535 km
(0 - 40, 723 miles)

ENG OIL TEMP

Engine: After warming up

More than 70°C (158°F)

A/F S1 HTR(B1)

Engine: After warming up, idle the engine (More than 260 seconds after starting engine.)

4 - 100%

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

SET VHCL SPD

Engine: Running

ASCD: Operating

The preset vehicle speed is displayed

MAIN SW

Ignition switch: ON

MAIN switch: Pressed

MAIN switch: Released

Off

CANCEL SW

Ignition switch: ON

CANCEL switch: Pressed

CANCEL switch: Released

Off

RESUME/ACC SW

Ignition switch: ON

RESUME/ACCELERATE switch: Pressed

RESUME/ACCELERATE switch: Released

Off

SET SW

Ignition switch: ON

SET/COAST switch: Pressed

SET/COAST switch: Released

Off

BRAKE SW1

Ignition switch: ON

Brake pedal: Fully released

Brake pedal: Slightly depressed

Off

BRAKE SW2

Ignition switch: ON

Brake pedal: Fully released

Off

Brake pedal: Slightly depressed

VHCL SPD CUT

Ignition switch: ON

Non

LO SPEED CUT

Ignition switch: ON

Non

AT OD MONITOR

Ignition switch: ON

Off

AT OD CANCEL

Ignition switch: ON

Off

CRUISE LAMP

Ignition switch: ON

MAIN switch: Pressed at the 1st time → at the 2nd time

On → Off

SET LAMP

NOTE: The item is indicated, but not used.

ALT DUTY

Engine speed: Idle

0 - 80%

BAT CUR SEN

Engine speed: Idle
Battery: Fully charged⁽²⁾
Selector lever: P or N (CVT)
Shifter lever: Neutral (M/T)
Air conditioner switch: OFF
No load

Approx. 2, 600 - 3, 500 mV

A/F ADJ-B1

Engine: running

-0.450 - 0.330

TUMBLE POS SEN

Ignition switch: ON
Engine coolant temperature: Between 0°C (32°F) and 45°C (113°F)

Accelerator pedal: Fully released

Less than 2.4 V

Accelerator pedal: Fully depressed

More than 3.5 V

P/N POSI SW

Ignition switch: ON

Selector lever: P or N (CVT)
Shifter lever: Neutral (M/T)

Selector lever: Except above

Off

INT/A TEMP SE

Ignition switch: ON

Indicates intake air temperature

AC PRESS SEN

Engine speed: Idle
Both A/C switch and blower fan switch: ON (Compressor operates)

1.0 - 4.0 V

VTC DTY EX B1

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

0 - 2%

2, 000 rpm

Approx. 0-90%

EVAP LEAK DIAG

Ignition switch: ON

Indicates the condition of EVAP leak diagnosis.

EVAP DIAG READY

Ignition switch: ON

Indicates the ready condition of EVAP leak diagnosis.

BAT TEMP SEN

Engine: After warming up, idle the engine
Selector lever: P or N
Air conditioner switch: OFF
No load

Indicates the temperature around the battery.

THRTL STK CNT B1

NOTE: The item is indicated, but not used.

A/F SEN1 DIAG1 (B1)

DTC P015A and P015B self-diagnosis is incomplete.

INCMP

DTC P015A and P015B self-diagnosis is complete.

CMPLT

A/F SEN1 DIAG2 (B1)

DTC P014C and P014D self-diagnosis is incomplete.

INCMP

DTC P014C and P014D self-diagnosis is complete.

CMPLT

A/F SEN1 DIAG3 (B1)

The vehicle condition is not within the diagnosis range of DTC P014C, P014D, P015A or P015B.

ABSNT

The vehicle condition is within the diagnosis range of DTC P014C, P014D, P015A or P015B.

PRSNT

HO2 S2 DIAG1 (B1)

DTC P0139 self-diagnosis (delayed response) is incomplete.

INCMP

DTC P0139 self-diagnosis (delayed response) is complete.

CMPLT

HO2 S2 DIAG2 (B1)

DTC P0139 self-diagnosis (slow response) is incomplete.

INCMP

DTC P0139 self-diagnosis (slow response) is complete.

CMPLT

EOP SENSOR

Engine: After warming up
Selector lever: P or N (CVT)
Shifter lever: Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

Approx. 1, 450 mV

2, 000 rpm

Approx. 2, 850 mV

SPORT MODE SWITCH

ignition switch: ON

Press the sport mode switch

Release the sport mode switch

Off

ECO MODE SWITCH

ignition switch: ON

Press the ECO mode switch

Release the ECO mode switch

Off

⁽¹⁾	Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ from ECM terminals voltage signal.

⁽²⁾	Before measuring the voltage, confirm that the battery is fully charged. Refer to "HOW TO HANDLE BATTERY ".