| FUEL INJECTION |
- Engine: Return to the original trouble condition
- Change the amount of fuel injection using CONSULT.
|
If trouble symptom disappears, see
Check item. |
- Harness and connectors
- Fuel injector
- Air fuel ratio (A/F) sensor 1
|
| ENG COOLANT TEMP |
- Engine: Return to the original trouble condition
- Change the engine coolant temperature using CONSULT.
|
If trouble symptom disappears, see
Check item. |
- Harness and connectors
- Engine coolant temperature sensor
- Fuel injector
|
| PURG VOL CONT/V |
- Engine: After warming up, run engine at 1, 500 rpm.
- Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.
|
Engine speed changes according to the opening percent. |
- Harness and connectors
- Solenoid valve
|
| FUEL/T TEMP SEN |
- Change the fuel tank temperature using CONSULT.
|
| COOLING FAN |
- Ignition switch: ON
- Select LOW or HIGH on CONSULT screen.
|
Cooling fan operates at low speed or high speed. |
- Harness and connectors
- Cooling fan motor
- Cooling fan relay
- IPDM E/R
|
| ALTERNATOR DUTY |
- Ignition switch: ON
- Change duty ratio using CONSULT.
|
Battery voltage changes. |
- Harness and connectors
- Alternator
- IPDM E/R
|
| FUEL PUMP RELAY |
- Ignition switch: ON (Engine stopped)
- Turn the fuel pump relay "ON" and "OFF" using CONSULT and listen to operating sound.
|
Fuel pump relay makes the operating sound. |
- Harness and connectors
- Fuel pump relay
|
| VIAS S/V-1 |
- Ignition switch: ON (Engine stopped)
- Turn Intake Manifold Tuning (IMT) Valve "ON" and "OFF" using CONSULT and listen to operating sound.
|
IMT valve motor makes an operating sound. |
- Harness and connectors
- IMT valve motor
|
| TUMBLE CONTROL VALVE |
- Ignition switch: ON
- Turn intake manifold runner control valve "ON" and "OFF" using CONSULT and listen to operating sound.
|
Intake Manifold Runner control valve motor makes an operating sound. |
- Harness and connectors
- Intake Manifold Runner control valve motor
|
| IGNITION TIMING |
- Engine: Return to the original trouble condition
- Timing light: Set
- Retard the ignition timing using CONSULT.
|
If trouble symptom disappears, see
Check item. |
Perform Idle Air Volume Learning. |
| POWER BALANCE |
- Engine: After warming up, idle the engine.
- A/C switch OFF
- Selector lever: P or N (CVT models)
- Shifter lever: Neutral (M/T models)
- Cut off each fuel injector signal one at a time using CONSULT.
|
Engine runs rough or stops. |
- Harness and connectors
- Compression
- Fuel injector
- Power transistor
- Spark plug
- Ignition coil
|
| VENT CONTROL/V |
- Ignition switch: ON (Engine stopped)
- Turn solenoid valve "ON" and "OFF" using CONSULT and listen to operating sound.
|
Solenoid valve makes an operating sound. |
- Harness and connectors
- Solenoid valve
|
| INT V/T ASSIGN ANGLE |
- Engine: Return to the original trouble condition
- Change intake valve timing using CONSULT.
|
If trouble symptom disappears, see
CHECK ITEM. |
- Harness and connectors
- Intake valve timing control solenoid valve
|
| EXH V/T ASSIGN ANGLE |
- Engine: Return to the original trouble condition
- Change exhaust valve timing using CONSULT.
|
If trouble symptom disappears, see
CHECK ITEM. |
- Harness and connectors
- Exhaust valve timing control solenoid valve
|