| REQ SW -DR [On/Off] |
* |
Indicates condition of door request switch LH. |
| REQ SW -AS [On/Off] |
* |
Indicates condition of door request switch RH. |
| REQ SW -BD/TR [On/Off] |
* |
Indicates condition of trunk open switch. |
| PUSH SW [On/Off] |
|
Indicates condition of push-button ignition switch. |
| CLUTCH SW [On/Off] |
* |
Indicates condition of clutch switch. |
| BRAKE SW 1 [On/Off] |
* |
Indicates condition of brake switch. |
| BRAKE SW 2 [On/Off] |
|
Indicates condition of brake switch. |
| DETE/CANCL SW [On/Off] |
* |
Indicates condition of P (park) position. |
| SFT PN/N SW [On/Off] |
* |
Indicates condition of P (park) or N (neutral) position. |
| UNLK SEN -DR [On/Off] |
* |
Indicates condition of driver door unlock sensor. |
| PUSH SW -IPDM [On/Off] |
|
Indicates condition of push-button ignition switch received from IPDM E/R on CAN communication line. |
| IGN RLY1 -F/B [On/Off] |
|
Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line. |
| DETE SW -IPDM [On/Off] |
|
Indicates condition of detent switch received from TCM on CAN communication line. |
| SFT PN -IPDM [On/Off] |
|
Indicates condition of P (park) or N (neutral) position from TCM on CAN communication line. |
| SFT P -MET [On/Off] |
|
Indicates condition of P (park) position from TCM on CAN communication line. |
| SFT N -MET [On/Off] |
|
Indicates condition of N (neutral) position from IPDM E/R on CAN communication line. |
| ENGINE STATE [Stop/Start/Crank/Run] |
* |
Indicates condition of engine state from ECM on CAN communication line. |
| VEH SPEED 1 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from ABS on CAN communication line. |
| VEH SPEED 2 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from combination meter on CAN communication line. |
| DOOR STAT-DR [LOCK/READY/UNLK] |
* |
Indicates condition of driver side door status. |
| DOOR STAT-AS [LOCK/READY/UNLK] |
* |
Indicates condition of passenger side door status. |
| ID OK FLAG [Set/Reset] |
|
Indicates condition of Intelligent Key ID. |
| PRMT ENG STRT [Set/Reset] |
|
Indicates condition of engine start possibility. |
| RKE OPE COUN1 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
| RKE OPE COUN2 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
| TRNK/HAT MNTR [On/Off] |
|
Indicates condition of trunk lid switch. |
| RKE-LOCK [On/Off] |
|
Indicates condition of lock signal from Intelligent Key. |
| RKE-UNLOCK [On/Off] |
|
Indicates condition of unlock signal from Intelligent Key. |
| RKE-TR/BD [On/Off] |
|
Indicates condition of trunk open signal from Intelligent Key. |
| RKE-PANIC [On/Off] |
|
Indicates condition of panic signal from Intelligent Key. |
| RKE-MODE CHG [On/Off] |
|
Indicates condition of mode change signal from Intelligent Key. |