LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Acura >> 2000 >> 3.5RL >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Component Tests >> Set/Resume/Cancel Switch Test >> 3.2TL
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Set/Resume/Cancel Switch Test: 3.2TL

  1. Disable air bag system. See appropriate AIR BAG RESTRAINT SYSTEMS article. Remove steering column covers. Disconnect SET/RESUME/CANCEL switch 4-pin connector. See Fig 1 .
  2. With SET button in ON position, continuity should exist between SET/RESUME/CANCEL switch 4-pin connector terminals No. 2 and 4. See Fig 1 . With RESUME button in ON position, continuity should exist between SET/RESUME/CANCEL switch 4-pin connector terminals No. 2 and 3. With CANCEL button in ON position, check for continuity by probing SET/RESUME/CANCEL switch 4-pin connector terminal No. 2 with positive terminal of DVOM, and terminals No. 3 and 4 with negative terminal of DVOM. With CANCEL button in ON position, continuity should exists between SET/RESUME/CANCEL switch 4-pin connector terminals No. 2 and 4 and between terminals No. 2 and 3. If continuity exists, go to next step. If continuity does not exist, go to step  5 .
  3. Remove instrument panel lower left cover and knee bolster. Disconnect in-line Blue 14-pin harness connector, located under left side of instrument panel, above driver's underdash fuse/relay box. Using DVOM, check for continuity in Light Green/Black wire between SET/RESUME/CANCEL switch 4-pin harness connector terminal No. 3 and in-line Blue 14-pin harness connector terminal No. 8. Also check for continuity in Light Green/Red wire between SET/RESUME/CANCEL switch 4-pin harness connector terminal No. 4 and in-line Blue 14-pin harness connector terminal No. 7. If continuity exists, go to next step. If continuity does not exist, replace wiring harness.
  4. Disconnect in-line Blue 16-pin harness connector, located behind glove box. Using DVOM, check for continuity in Light Green/Blue wire between SET/RESUME/CANCEL switch 4-pin harness connector terminal No. 2 and in-line Blue 16-pin harness connector terminal No. 9. See Fig 2 . If continuity exists, go to next step. If continuity does not exist, replace wiring harness.
  5. Remove SET/RESUME/CANCEL switch. See SET/RESUME/CANCEL SWITCH  under REMOVAL & INSTALLATION. With SET button in ON position, continuity should exist between SET/RESUME/CANCEL switch connector terminals No. 1 and 3. See Fig 2 . With RESUME button in ON position, continuity should exist between SET/RESUME/CANCEL switch connector terminals No. 1 and 2. Go to next step.
  6. With CANCEL button in ON position, check for continuity by probing SET/RESUME/CANCEL switch 4-pin connector terminal No. 2 with positive terminal of DVOM, and terminals No. 3 and 4 with negative terminal of DVOM. With CANCEL button in ON position, continuity should exists between SET/RESUME/CANCEL switch 4-pin connector terminals No. 2 and 4 and between terminals No. 2 and 3. If continuity does not exist, replace switch. If exists, replace cable reel. See appropriate AIR BAG RESTRAINT SYSTEMS article.
Fig 1: Identifying Combination Light Switch & Main Wiring Harness Connector Terminals (3.2TL)
G99B50089Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fig 2: Identifying Combination Light Switch & Right Engine Compartment Wiring Harness Connector Terminals (3.2TL)
G99E50090Courtesy of AMERICAN HONDA MOTOR CO., INC.
scientia non olet · About LEMON Manuals