| Cruise control cannot be set |
- Check the No. 10 (20 A) fuse in the under-hood fuse/relay box, and the No. 13 (15 A) fuse in the driver's under-dash fuse/relay box.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
|
Poor ground G101(A/T model) or G301 (M/T model) |
| Cruise control can be set, but the cruise main indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION
).
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control main switch signal input.
|
Faulty gauge control module |
| Cruise control can be set, but the cruise control indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION
).
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control indicator signal input.
|
Faulty gauge control module |
| Vehicle does not accelerate accordingly when the resume/accel button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the resume/accel switch signal input.
|
Open circuit, loose or disconnected terminals: ORN, GRY wire |
| Set speed does not cancel when the brake pedal is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the brake pedal position switch test (see BRAKE PEDAL POSITION SWITCH TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the brake pedal position switch signal input.
|
- Short to power on the ORN wire
- Faulty brake pedal position switch
|
| Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T model) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the clutch pedal position switch B test (see CLUTCH PEDAL POSITION SWITCH B TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the clutch pedal position switch B signal input.
|
Short to ground on the BRN wire |
| Set speed does not cancel when the cruise control main button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control main switch signal input.
|
Short to ground on the YEL wire |
| Set speed does not cancel when the cancel button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cancel switch signal input.
|
Open circuit, loose or disconnected terminals: LT GRN or ORN, GRY wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the brake pedal position switch adjustment (see BRAKE PEDAL AND BRAKE PEDAL POSITION SWITCH ADJUSTMENT
.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the resume/accel switch signal input.
Test the brake pedal position switch signal input.
|
- Open circuit, loose or disconnected terminals: ORN, GRY wire
- Faulty brake pedal position switch
|
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T model) |
- Check for PGM-FI DTCs(see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the clutch pedal position switch B adjustment (see
CLUTCH PEDAL, CLUTCH PEDAL POSITION SWITCH A, AND CLUTCH PEDAL POSITION SWITCH B ADJUSTMENT
.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the resume/accel switch signal input.
Test the clutch pedal position switch B signal input.
|
- Open circuit loose or disconnected terminal: LT BLU, GRY wire
- Faulty clutch pedal position switch B
|
| With the ignition switch in ON (II), or the vehicle ignition in the ON mode, and the lighting switch turned on, the cruise control combination switch illumination does not come on |
Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
). |
|