| Cruise control cannot be set |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the No. 13 (20 A) fuse in the under-hood fuse/ relay box, and the No. 18 (15 A) fuse in the under-dash fuse/relay box.
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Poor ground G501 |
| Cruise control can be set, but the cruise main indicator does not come on |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
|
Faulty gauge control module |
| Cruise control can be set, but the cruise control indicator does not come on |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cruise control indicator signal input.
|
Faulty gauge control module |
| Vehicle does not decelerate or accelerate accordingly when the set/ decel or resume/accel switch is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the set/decel, resume/accel switch signal input.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Open circuit, loose or disconnected terminals: YEL/WHT or GRN/YEL wire |
| Set speed does not cancel when the brake pedal is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the brake pedal position switch signal input.
- Do the brake pedal position switch test (see
BRAKE PEDAL POSITION SWITCH TEST
).
|
- Short to power in the BRN/YEL wire
- Faulty brake pedal position switch
|
| Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the clutch pedal position switch signal input.
- Do the clutch pedal position switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Short to ground in the LT BLU wire |
| Set speed does not cancel when the cruise control main switch is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cruise control main switch signal input.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Short to ground in the BRN wire |
| Set speed does not cancel when the cancel switch is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cancel switch signal input.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Open circuit, loose or disconnected terminals: YEL/WHT or GRN/YEL wire |
| Set speed will not resume when the resume/accel switch is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the brake pedal position switch adjustment (see
BRAKE PEDAL AND BRAKE PEDAL POSITION SWITCH ADJUSTMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the resume/accel switch signal input. Test the brake pedal position switch signal input.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
- Open circuit, loose or disconnected terminals: YEL/WHT wire
- Faulty brake pedal position switch
|
| Set speed will not resume when the resume/accel switch is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the clutch pedal position switch adjustment (see
CLUTCH PEDAL, CLUTCH PEDAL POSITION SWITCH, AND CLUTCH INTERLOCK SWITCH ADJUSTMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the resume/accel switch signal input. Test the clutch pedal position switch signal input.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
- Open circuit, loose or disconnected terminals: YEL/WHT wire
- Faulty clutch pedal position switch
|
| With the ignition switch ON (II), and the lighting switch turned on, the cruise control combination switch illumination does not come on |
Replace the cruise control combination switch (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
). |
|