| Cruise control cannot be set |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Check the No. 10 (20 A) fuse in the under-hood fuse/relay box, and the No. 13 (15 A) fuse in the driver's under-dash fuse/relay box.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
|
Poor ground G301 (M/T model) or G101 (A/T model) |
| Cruise control can be set, but the cruise main indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cruise control main switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Faulty gauge control module |
| Cruise control can be set, but the cruise control indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cruise control indicator signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Faulty gauge control module |
| Vehicle does not accelerate accordingly when the resume/accel button is pressed |
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the resume/accel switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: ORN or GRY wire |
| Set speed does not cancel when the brake pedal is pressed |
- Do the brake pedal position switch test (see
BRAKE PEDAL POSITION SWITCH TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the brake pedal position switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
- Short to power on the ORN wire
- Faulty brake pedal position switch
|
| Set speed does not cancel (engine RPM stays high) when the clutch pedal is pressed (M/T model) |
- Do the clutch pedal position switch B test (see CLUTCH PEDAL POSITION SWITCH B TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the clutch pedal position switch B signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Short to ground in the BRN wire |
| Set speed does not cancel when the cruise control main button is pressed |
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cruise control main switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Short to ground in the YEL wire |
| Set speed does not cancel when the cancel button is pressed |
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the cancel switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: LT GRN, ORN or GRY wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal) |
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the resume/accel switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: ORN or GRY wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T model) |
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
). Test the resume/accel switch signal input.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit loose or disconnected terminal: LT BLU or GRY wire |
| Light switch turned on, the cruise control combination switch illumination does not come on |
- Check the No. 6 (7.5 A) fuse in the passenger's under-dash fuse/relay box.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
|
Open circuit, loose or disconnected terminals: GRY or RED wires |