DTC P2195: Rear A/F Sensor (Bank 1, Sensor 1) Signal Stuck Lean; DTC P2197: Front A/F Sensor (Bank 2, Sensor 1) Signal Stuck Lean

NOTE:

Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
Information marked with an asterisk (*) applies to the front bank (Bank 2).
If the vehicle was out of fuel and the engine stalled before this DTC was stored, refuel, and clear the DTC with the HDS.
If DTC P2101, P2118, P2135, P2138, P2176, or a combination of P2122 and P2127, P2122 and P2138, or P2127 and P2138 is stored at the same time as DTC P2195 (P2197)*, troubleshoot those DTCs first, then recheck for DTC P2195 (P2197)*.

Check for dirt or debris on the MAF sensor/IAT sensor.
Is it dirty?

YES - Remove the debris. If needed, replace the MAF sensor/IAT sensor , then go to step 9.

NO - Go to step 2.
Check the installation of the A/F sensor (Sensor 1).
Is the A/F sensor loose or disconnected from the exhaust pipe?

YES - Go to step 7.

NO - Go to step 3.
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
Clear the DTC with the HDS.
Start the engine, and let it idle for 2 minutes.
Check for Pending or Confirmed DTCs with the HDS.
Is DTC P2195 and/or P2197* indicated?

YES - Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 14.

NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM. If any other Pending or Confirmed DTCs are indicated, go to the indicated DTC's troubleshooting. ■
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
Reinstall the A/F sensor (Sensor 1) .
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
Reset the ECM/PCM with the HDS.
Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
Check for Pending or Confirmed DTCs with the HDS.
Is DTC P2195 and/or P2197* indicated?

YES - Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1.

NO - Go to step 13.
Monitor the OBD STATUS for DTC P2195 and/or P2197* in the DTCs MENU with the HDS.
Does the screen indicate PASSED?

YES - Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 12, go to the indicated DTC's troubleshooting. ■

NO - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, keep idling until a result comes on.
Update the ECM/PCM if it does not have the latest software (see ECM/PCM Update ), or substitute a known-good PCM (see SUBSTITUTING THE ECM/PCM ).
Start the engine, and let it idle for 2 minutes.
Check for Pending or Confirmed DTCs with the HDS.
Is DTC P2195 and/or P2197* indicated?

YES - Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then go to step 15. If the ECM/PCM was substituted, go to step 1.

NO - Go to step 17.
Monitor the OBD STATUS for DTC P2195 and/or P2197* in the DTCs MENU with the HDS.
Does the screen indicate PASSED?

YES - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM Replacement ). If any other Pending or Confirmed DTCs were indicated instep 16, go to the indicated DTC's troubleshooting. ■

NO - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then go to step 15. If the ECM/PCM was substituted, go to step 1. If the screen indicates NOT COMPLETED, keep idling until a result comes on.