LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Acura >> 2016 >> RLX Base >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Security System / Keyless Entry System - Symptom Troubleshooting (Except Hybrid) >> Keyless Access System Symptom Troubleshooting >> Cannot select ON mode with keyless access, but can select ON mode with the keyless remote touching the engine start/stop switch (2014 2015 2016 2017)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Cannot select ON mode with keyless access, but can select ON mode with the keyless remote touching the engine start/stop switch (2014 2015 2016 2017)

  1. Keyless access system check 1

    -1. Push the LOCK and the UNLOCK buttons of the keyless remote, and check if the LED on the keyless remote comes on.

    Does the LED come on?

    YES 

    Go to step 2.

    NO 

    Replace the keyless remote battery, inspect the water dot, and recheck the system. If the symptom does not go away, replace the keyless remote.

  2. Keyless access system check 2

    -1. Touch the engine start/stop switch with the keyless remote. The buttons on the keyless remote should be facing you.

    -2. Turn the vehicle to the ON mode.

    -3. Select KEYLESS ACCESS CONTROL UNIT from the ONE-PUSH START system select menu with the HDS, and enter SELF CHECK.

    One-Push - KEYLESS ACCESS CONTROL UNIT- SELF CHECK

    Does the system communicate with the HDS?

    YES 

    Go to step 3.

    NO 

    Do the keyless access control unit input test .

  3. PCU DTC check

    -1. Check for PCU DTCs with the HDS.

    DTC Description DTC
       

    Are any DTCs indicated?

    YES 

    Troubleshoot the PCU DTCs.

    NO 

    Go to step 4.

  4. Keyless access DTC check

    -1. Check for keyless access control unit DTCs with the HDS.

    DTC Description DTC
       

    Are any DTCs indicated?

    YES 

    Troubleshoot the keyless access control unit DTCs.

    NO 

    Go to step 5.

  5. Backup DTC check

    -1. Check for backup control unit DTCs with the HDS.

    DTC Description DTC
       

    Are any DTCs indicated?

    YES 

    Troubleshoot the backup control unit DTCs.

    NO 

    Go to step 6.

  6. Keyless access system check 3

    -1. Select HISTORY DATA from the KEYLESS ACCESS CONTROL UNIT mode menu with the HDS.

    One-Push - KEYLESS ACCESS CONTROL UNIT- HISTORY DATA

    Select HISTORY CLEAR, and back to TEST MODE MENU.

    -3. Turn the vehicle to the OFF (LOCK) mode.

    -4. Touch the engine start/stop switch with the keyless remote. The buttons on the keyless remote should be facing you.

    -5. Turn the vehicle to the ON mode.

    -6. Select HISTORY DATA from the KEYLESS ACCESS CONTROL UNIT mode menu with the HDS.

    One-Push - KEYLESS ACCESS CONTROL UNIT- HISTORY DATA

    History Data 

    ENGINE START/STOP SWITCH 1 (+) ON
    ENGINE START/STOP SWITCH 2 (-) ON

    Is all the information ON?

    YES 

    Go to step 8.

    NO 

    Go to step 7.

  7. Open wire check (SS1 (+), SS2 (-) lines)

    -1. Turn the vehicle to the OFF (LOCK) mode.

    -2. Disconnect the following connectors.

    Engine start/stop switch 10P connector
    Keyless access control unit connector B (28P)

    -3. Check for continuity between test points 1 and 2 respectively.

    Test condition Vehicle OFF (LOCK) mode Engine start/stop switch 10P connector: disconnected
    Keyless access control unit connector B (28P): disconnected
    Test circuit SS1 (+)
    Test point 1 Keyless access control unit connector B (28P) No. 12 (GRY)
    Test point 2 Engine start/stop switch 10P connector No. 4 (GRY)
    Test circuit SS2 (-)
    Test point 1 Keyless access control unit connector B (28P) No. 8 (BLU)
    Test point 2 Engine start/stop switch 10P connector No. 1 (BLU)
    GHH350700Courtesy of HONDA, U.S.A., INC.

    Is there continuity?

    YES 

    The SS1 (+) and SS2 (-) wires are OK. Replace the keyless access control unit .

    NO 

    Repair an open or high resistance in the wire.

  8. Keyless access system check 4

    -1. Select KEYLESS TRANSMITTER from the BODY ELECTRICAL SYSTEM SELECT menu, then select INSPECTION, then KEYLESS CHECK.

    Inspection - Keyless Check

    Do the KEYLESS CHECK with the HDS using the all keyless remotes.

    Is DIFFERENT KEYLESS ENTRY TRANSMITTER CODE IS RECEIVED indicated?

    YES 

    Go to step 11.

    NO 

    Go to step 9.

  9. Keyless remote check (substitution)

    -1. Substitute a known-good keyless remote, then recheck the system.

    Does the system change to ON mode?

    YES 

    Register the keyless remote , and recheck. If the symptom does not go away, replace the keyless remote.

    NO 

    Go to step 10.

  10. RF unit (substitution)

    -1. Substitute a known-good RF unit, then recheck the system.

    Does the system change to ON mode?

    YES 

    Replace the original RF unit .

    NO 

    Replace the keyless access control unit .

  11. Keyless remote check (substitution)

    -1. Substitute a known-good keyless remote, then recheck the system.

    Does the system change to ON mode?

    YES 

    Register the keyless remote , and recheck. If the symptom does not go away, replace the keyless remote.

    NO 

    Go to step 12.

  12. RF unit (substitution)

    -1. Substitute a known-good RF unit, then recheck the system.

    Does the system change to ON mode?

    YES 

    Replace the original RF unit .

    NO 

    Replace the keyless access control unit .

scientia non olet · About LEMON Manuals