DTC P1174
DTC P1174: Front Air/Fuel Ratio (A/F) Sensor (Bank 2, Sensor 1) Circuit Out of Range High
General Description
If a malfunction causes the front air/fuel ratio (A/F) sensor (bank 2, sensor 1) signal to the powertrain control module (PCM) to deviate from the normal control area, the front A/F sensor (bank 2, sensor 1) may still become active after the engine starts, but the air/fuel feedback does not start normally and the emissions deteriorate. When the front A/F sensor (bank 2, sensor 1) output is out of the normal area, and this condition continues after the front A/F sensor (bank 2, sensor 1) is active, the PCM detects a malfunction and stores a DTC.
Monitor Execution, Sequence, Duration, DTC Type, OBD Status
| Execution | Continuous |
| Sequence | None |
| Duration | 7.0 seconds or more |
| DTC Type | Two drive cycles, MIL on |
| OBD Status | PASSED/FAILED/EXECUTING/OUT OF (TEST) CONDITION |
Enable Conditions
| Condition | |
|---|---|
| No active DTCs set (prevents monitor from running)*1 | P0101, P0102, P0103, P0107, P0108, P0117, P0118, P0154, P0155, P0174, P0175, P0204, P0205, P0206, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0339, P0351, P0352, P0353, P0354, P0355, P0356, P0443, P0496, P0497, P0627, P1128, P1129, P145C, P2197, P2240, P2241, P2247, P2249, P2254, P2255 |
| No active DTCs set (prevents monitor from running)*2 | P0101, P0102, P0103, P0107, P0108, P0117, P0118, P0154, P0155, P0174, P0175, P0204, P0205, P0206, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0339, P0354, P0355, P0356, P0441, P0443, P0496, P0497, P0627, P2073, P2074, P2197, P2240, P2241, P2247, P2249, P2254, P2255 |
| No active DTCs set (prevents monitor from running)*3 | P006A, P0102, P0103, P0107, P0108, P0117, P0118, P0154, P0155, P0174, P0175, P0204, P0205, P0206, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0339, P0354, P0355, P0356, P0441, P0443, P04DF, P04F1, P0627, P2073, P2074, P2197, P2240, P2241, P2247, P2249, P2254, P2255 |
*1: 2014 - 2015 models
*2: 2016 model
*3: 2017 model on and after
Malfunction Threshold
A malfunction is detected when the front A/F sensor (bank 2, sensor 1) output voltage is 4.7 V or more.
Possible Cause
NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
- Front A/F sensor (bank 2, sensor 1) failure
Confirmation Procedure
Operating Condition
- 1.
Start the engine. Hold the engine speed [ENGINE SPEED] at 3000 RPM without load (in P or N) until the radiator fan comes on, then let it idle.
- 2.
Air/fuel ratio feedback is started while idling, hold for at least 7 seconds.
[ ]: HDS Parameter
With the HDS
None.
Diagnosis Details
Conditions for setting the DTC
When a malfunction is detected during the first drive cycle, a Pending DTC is stored in the PCM memory. If the malfunction returns in the next (second) drive cycle, the MIL comes on and a Confirmed DTC and the freeze data are stored.
Conditions for clearing the DTC
The MIL is cleared if the malfunction does not return in three consecutive trips in which the diagnostic runs. The MIL, the Pending DTC, the Confirmed DTC, and the freeze data can be cleared with the scan tool Clear command or by disconnecting the battery.