DTC Advanced Diagnostics: P2817
DTC P2817 : Shift Solenoid Valve O/P Stuck OFF
General Description
Transmission fluid pump volume changes by shift solenoid valve O/P ON/OFF control
| Transmission fluid pump volume | Shift Solenoid Valve O/P |
|---|---|
| High | OFF |
| Low | ON |
The shift solenoid valve O/P controls the drain circuit close/open commanded by the transmission control module (TCM) ON/OFF commands. The transmission fluid pump volume is changed by switching the shift solenoid valve O/P ON/OFF control. The TCM commands the driver circuit to turn on the shift solenoid valve O/P. The TCM temporarily increases the driven pulley pressure up to target value. As the commanded driven pulley pressure reaches the target value, the TCM monitors the driven pulley pressure when the shift solenoid valve O/P is ON and OFF. If the driven pulley pressure does not change, the TCM detects a shift solenoid valve O/P stuck OFF malfunction and stores a DTC.
Monitor Execution, Sequence, Duration, DTC Type
| Execution | Once per driving cycle |
| Sequence | None |
| Duration | 10 seconds or less |
| DTC Type | Two drive cycles, MIL off, Shift position indicator blinks |
Enable Conditions
| Condition | Minimum | Maximum |
|---|---|---|
| Engine speed [Engine Speed] | 700 rpm | 750 rpm |
[ ]: HDS Parameter
| Condition | Minimum | Maximum |
|---|---|---|
| Transmission fluid temperature [CVTF Temperature] | 248 deg.F (120 deg.C) | - |
| Vehicle speed [Vehicle Speed] | - | 1 mph (3 km/h) |
| Shift lever position/mode | D | |
| Other | Accelerator pedal released | |
| Brake pedal pressed | ||
[ ]: HDS Parameter
Malfunction Threshold
Judgments 1 and 2 are executed sequentially, and if the driven pulley pressure does not change when the shift solenoid valve O/P [Shift Sol O/P] is ON and OFF.
| Judgment | Shift solenoid valve O/P | Commanded driven pulley pressure | Driven pulley pressure | Detection time |
|---|---|---|---|---|
| 1 | OFF | About 1, 961 kPa(20.0 kgf/cm 2, 284 psi) | About 1, 961 kPa(20.0 kgf/cm 2, 284 psi) | 5.0 seconds |
| 2 | ON | About 1, 961 kPa(20.0 kgf/cm 2, 284 psi) | About 1, 961 kPa(20.0 kgf/cm 2, 284 psi) | 5.0 seconds |
Possible Cause
The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
- Shift solenoid valve O/P stuck off
Confirmation Procedure
Operating Condition
- Start the engine.
- With the brake pedal pressed, place the shift lever in from N position/mode to D position/mode.
- Accelerate the vehicle to 12 mph (20 km/h).
- Stop and leave the vehicle for at least 10 seconds.
- Turn the vehicle to the OFF (LOCK) mode.
- Repeat Driving Pattern steps 1 through 4.
- Drive the vehicle in this manner only if the traffic regulations and ambient conditions allow.
Diagnosis Details
Conditions for setting the DTC
When a malfunction is detected during the first drive cycle, a Pending DTC is stored in the TCM memory. If the malfunction returns in the next (second) drive cycle, the shift position indicator blinks and a Confirmed DTC and the freeze data are stored. The MIL does not come on.
Conditions for clearing the DTC
The shift position indicator comes off by turning the vehicle to the OFF (LOCK) mode. The Pending DTC, the Confirmed DTC, and the freeze data can be cleared with the scan tool clear command.