Repair Procedure

How to use this manual .

Courtesy of HONDA, U.S.A., INC.

: Torque, N.m (lbf.ft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

: ■SPL Tool

: Required Removal

Courtesy of HONDA, U.S.A., INC.

: Torque, N.m (lbf.ft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

: ■SPL Tool

: Required Removal

Courtesy of HONDA, U.S.A., INC.

: Torque, N.m (lbf.ft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

: ■SPL Tool

: Required Removal

1. A.-

   Sub-Procedure 

   Figure 1 

   Removal 

   1. Turn the vehicle to the ON mode.

   2. Turn and hold the wiper/washer switch to the MIST position, and then turn the vehicle to the OFF (LOCK) mode.

   3. Release the wiper/washer switch.

   NOTE:

   The wiper arm stops at the service position.

   4. On the "SET" label (a) side, pull back the wiper blade (b). (Figure 1)

   Courtesy of HONDA, U.S.A., INC.

   Figure 2 

   5. Pull out the wiper blade (c). (Figure 2)

   Courtesy of HONDA, U.S.A., INC.

   Figure 3 

   6. If necessary, remove the end cap (d) by pressing the tab (e). (Figure 3)

   NOTE:  When removing it, take care not to damage the rubber holder (f). (Figure 3)

   Courtesy of HONDA, U.S.A., INC.

2. B.-

   Sub-Procedure 

   Courtesy of HONDA, U.S.A., INC.

   Removal 

   1. Turn the vehicle to the ON mode.

   2. Turn and hold the wiper/washer switch to the MIST position, and then turn the vehicle to the OFF (LOCK) mode.

   3. Release the wiper/washer switch.

   NOTE:

   The wiper arm stops at the service position.

   4. Remove the wiper blade holder (a).

   After Installation 

   • Wiper Arm Adjustment
3. C.-

   NOTE:  Before removal, turn the wiper/washer switch ON to the (LO) or (HI) position, then OFF to return the motor shaft to the park position.

   After Installation 

   • Wiper Arm Adjustment
4. D.-

   Courtesy of HONDA, U.S.A., INC.

5. E.-

   Courtesy of HONDA, U.S.A., INC.

6. F.-

   Courtesy of HONDA, U.S.A., INC.

7. G.-

   Courtesy of HONDA, U.S.A., INC.

8. H.-

   Sub-Procedure 

   Removal 

   • Refer to the figure.

   Courtesy of HONDA, U.S.A., INC.

9. I.-

   Sub-Procedure 

   Courtesy of HONDA, U.S.A., INC.

   ? Removal 

   • Refer to the figure.
10. J.-

    Courtesy of HONDA, U.S.A., INC.

    Sub-Procedure 

    Installation 

    NOTE:

    Do not wipe off part (a) because special grease is applied.

    After Installation 

    • Wiper Arm Adjustment
11. K.-

    Key Information 

    Do the following before starting your work.

    Remove: 

    • Left Front Inner Fender (as needed)

    Sub-Procedure 

    Removal 

    • Refer to the figure.

    Courtesy of HONDA, U.S.A., INC.

12. L.-

    Courtesy of HONDA, U.S.A., INC.

13. M.-

    Courtesy of HONDA, U.S.A., INC.

14. N.-

    Sub-Procedure 

    Courtesy of HONDA, U.S.A., INC.

    Removal 

    • Refer to the figure.
15. O.-

    Sub-Procedure 

    Courtesy of HONDA, U.S.A., INC.

    Installation 

    • Set the motor (a) and the wiper linkage assembly (b).
    NOTE:

    • Install the provided self-tapping bolts (c).
    • Do not use air tools and impact wrenches.
    • Keep the bolts perfectly straight while bolting them in.

    Tightening Procedure 

    Step	Operation	Object	Specification
    1	Tighten (Tapping)	All bolts	The bolts until they sit on the linkage.
    2	Loosen	All bolts	-
    3	Tighten	All bolts	-

    After Installation 

    • Wiper Arm Adjustment
16. P.-

    Sub-Procedure 

    Courtesy of HONDA, U.S.A., INC.

    Installation 

    • Set the windshield wiper motor to the park position.

      NOTE:  Connect the wiper motor connector, and turn the wiper/washer switch ON to (LO) or (HI) position, then OFF to return the wiper motor shaft to the park position.

    • Align the marks (a).

    After Installation 

    • Wiper Arm Adjustment
17. Q.-

    Sub-Procedure 

    Courtesy of HONDA, U.S.A., INC.

    Installation 

    Lubricant Specifications 

    Position	Type
    a	Multipurpose Grease