Module, Adaptive Cruise Control (Acc)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C1200-16 | BATTERY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1200-17 | BATTERY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C1400-86 | MASTER CYLINDER PRESSURE FAULT - SIGNAL INVALID |
| C1401-86 | WHEEL SPEED PLAUSIBILITY FAILURE - SIGNAL INVALID |
| C1402-86 | MULTI AXIS ACCELERATION SENSORS FROM BRAKE SYSTEM MODULE (BSM) FAILURE - SIGNAL INVALID |
| C1403-86 | ELECTRICAL POWER STEERING FAILURE - SIGNAL INVALID |
| C1404-86 | ENGINE SIGNAL FAILURE - SIGNAL INVALID |
| C1405-86 | TRAILER TOW MODULE FAIL - SIGNAL INVALID |
| C1406-86 | BRAKE SWITCH PLAUSIBILITY - SIGNAL INVALID |
| C1407-86 | ACKNOWLEDGE SIGNAL FAIL FROM BRAKE SYSTEM MODULE - SIGNAL INVALID |
| C1408-86 | ELECTRONIC STABILITY CONTROL (ESC) FAIL STATUS PRESENT - SIGNAL INVALID |
| C1409-97 | RADAR SENSOR BLIND - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C140A-55 | VEHICLE EOL CONFIGURATION - NOT CONFIGURED |
| C140B-05 | VEHICLE EOL CONFIGURATION FAULT - SYSTEM PROGRAMMING FAILURE |
| C140C-86 | DRIVER ASSISTANT SYSTEM MODULE (DASM) INTERVENTION REQUEST TIME OUT OF RANGE - SIGNAL INVALID |
| C140D-86 | SEAT BELT INFORMATION FAILURE - SIGNAL INVALID |
| C1410-87 | C2_IGW1 MESSAGE FROM BODY COMPUTER MISSING - MISSING MESSAGE |
| C1411-49 | CONTROL UNIT - INTERNAL ELECTRONIC FAILURE |
| C1412-54 | CALIBRATION PROCEDURE - MISSING CALIBRATION |
| C1413-86 | EXTERNAL LIGHT MESSAGE - SIGNAL INVALID |
| C1413-87 | EXTERNAL LIGHT MESSAGE - MISSING MESSAGE |
| C1414-87 | CLUSTER 2 MESSAGE ABSENT FROM INSTRUMENT PANEL CLUSTER (IPC) - MISSING MESSAGE |
| C1415-53 | MANUFACTURING MODE - DEACTIVATED |
| C1417-78 | HORIZONTAL MISALIGNMENT SENSOR - ALIGNMENT OR ADJUSTMENT INCORRECT |
| C1418-78 | VERTICAL MISALIGNMENT SENSOR - ALIGNMENT OR ADJUSTMENT INCORRECT |
| C1419-64 | INTERNAL WHEEL SPEED PLAUSIBILITY FAILURE - SIGNAL PLAUSIBILITY FAILURE |
| C141A-64 | INTERNAL STEERING WHEEL ANGLE PLAUSIBILITY FAILURE - SIGNAL PLAUSIBILITY FAILURE |
| C141B-97 | VIDEO CAMERA BLIND - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C141C-86 | VIDEO CAMERA PRIVATE CAN COMMUNICATION FAILURE - SIGNAL INVALID |
| C141D-47 | MICRO-CONTROLLER FAILURE - WATCHDOG SAFETY MICRO-CONTROLLER FAILURE |
| C141E-49 | COMPONENT INTERNAL COMMUNICATION FAILURE - INTERNAL ELECTRONIC FAILURE |
| C141F-96 | HARDWARE RESET FAILURE - COMPONENT INTERNAL FAILURE |
| C1420-25 | RADAR SIGNAL FAILURE - SIGNAL SHAPE WAVEFORM FAILURE |
| C1420-66 | RADAR SIGNAL FAILURE - SIGNAL HAS TOO MANY TRANSITIONS EVENTS |
| C1421-64 | INTERNAL MULTI AXIS ACCELERATION PLAUSIBILITY FAILURE - SIGNAL PLAUSIBILITY FAILURE |
| C1422-49 | INTERNAL HW PLAUSIBILITY CHECK - INTERNAL ELECTRONIC FAILURE |
| C1422-66 | INTERNAL HW PLAUSIBILITY CHECK - SIGNAL HAS TOO MANY TRANSITIONS EVENTS |
| C1423-4B | SENSOR INTERNAL TEMPERATURE - OVER TEMPERATURE |
| C1424-4B | COMPONENT INTERNAL TEMPERATURE - OVER TEMPERATURE |
| C1425-45 | FLASHED SW IN ECU NOT COMPATIBLE - PROGRAM MEMORY FAILURE |
| C1426-49 | CONTROL UNIT PERMANENT FAILURE - INTERNAL ELECTRONIC FAILURE |
| C1428-68 | RADAR UNAVAILABILITY SITUATION - EVENT INFORMATION |
| C1429-66 | RADAR HW OVERTEMPERATURE - SIGNAL HAS TOO MANY TRANSITIONS EVENTS |
| C1429-68 | RADAR HW OVERTEMPERATURE - EVENT INFORMATION |
| C1430-86 | VIN PLAUSIBILITY CHECK FAILURE - SIGNAL INVALID |
| C1431-86 | YAW RATE ACCELERATION SENSOR FROM BRAKE SYSTEM MODULE (BSM) FAILURE - SIGNAL INVALID |
| C1432-86 | TURN INDICATOR SIGNAL FAILURE FROM BODY CONTROL MODULE (BCM) - SIGNAL INVALID |
| C1433-86 | EXTERNAL BRAKE SIGNAL FAILURE FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1434-86 | BRAKE JERK REQUEST NOT PLAUSIBLE - SIGNAL INVALID |
| C1435-87 | STATUS EPB MESSAGE FROM BRAKE SYSTEM MODULE (BSM) ABSENT - MISSING MESSAGE |
| C1436-86 | ELECTRIC PARKING BRAKE SYSTEM FAIL - SIGNAL INVALID |
| C1438-86 | GAS PEDAL POSITION SIGNALS FROM ENGINE CONTROL MODULE (ECM) - SIGNAL INVALID |
| C1439-86 | ENGINE TORQUE SIGNALS FROM ENGINE CONTROL MODULE (ECM) - SIGNAL INVALID |
| C1443-87 | TRANSM MESSAGE (FROM DUAL CLUTCH TRANSMISSION MODULE) FOR ADAPTIVE CRUISE CONTROL FUNCTION - MISSING MESSAGE |
| C1445-87 | SCCM CRS CTRL MESSAGE FROM STEERING COLUMN CONTROL MODULE FOR ADAPTIVE CRUISE CONTROL FUNCTION - MISSING MESSAGE |
| C1446-86 | CRUISE CONTROL INFORMATION FAIL - SIGNAL INVALID |
| C144A-86 | VEHICLE SPEED - SIGNAL INVALID |
| C144B-24 | ADAPTIVE CRUISE CONTROL (ACC) FUNCTION BUTTON STUCK - SIGNAL STUCK HIGH |
| C144D-86 | ENGINE TORQUE REQUEST NOT PLAUSIBLE - SIGNAL INVALID |
| C144F-86 | SIGNAL LIMPHOME STATUS ACTIVE FROM DCTM (DUAL CLUTCH TRANSMISSION MODULE) - SIGNAL INVALID |
| C1450-86 | ENGINE SPEED SIGNAL FAIL FROM ENGINE CONTROL MODULE (ECM) - SIGNAL INVALID |
| C1451-86 | ADAPTIVE CRUISE CONTROL (ACC) SAFE - SIGNAL INVALID |
| C1452-86 | ENGINE TORQUE DRIVE ASSISTANCE SYSTEM MODULE (DASM) - SIGNAL INVALID |
| C1453-86 | ACC INTERVENTION SIGNALS NOT PLAUSIBLE - SIGNAL INVALID |
| C1454-86 | DISPLAYED FUSE SPEED LIMIT FROM IPC-INSTRUMENT PANEL CLUSTER-SIGNAL INVALID |
| C1460-51 | APPLICATION AND OR CALIBRATION NOT PROGRAMMED-NOT PROGRAMMED |
| U0001-88 | C1 CAN BUS-BUS OFF |
| U1700-87 | BODY CONTROL MODULE (BCM) - MISSING MESSAGE |
| U1701-86 | ENGINE CONTROLLER (ECM) - SIGNAL INVALID |
| U1702-87 | ELECTRICAL POWER STEERING (EPS) - MISSING MESSAGE |
| U1703-87 | INSTRUMENT PANEL CLUSTER (IPC) - MISSING MESSAGE |
| U1706-86 | BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| U1726-87 | AIRBAG SYSTEM (ORC) - MISSING MESSAGE |
| U1730-87 | HAPTIC LANE FEEDBACK (HALF) MISSING MESSAGE |
| U1763-87 | TRAILER TOW MODULE (TTM) MISSING MESSAGE |
| U1930-86 | INTERNAL IGNITION WORKING CONDITION SIGNAL - SIGNAL INVALID |
| U1932-86 | IGNITION WORKING CONDITION FROM BODY COMPUTER MODULE NOT VALID - SIGNAL INVALID |
| U1933-87 | BCM COMMAND MESSAGE FROM BCM (BODY COMPUTER MODULE) ABSENT - MISSING MESSAGE |
| U1950-83 | MESSAGE COUNTER/CRC FAULT IN BCM COMMAND (FROM BODY CONTROL MODULE) MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1952-83 | MESSAGE COUNTER/CRC FAULT IN BRAKE 1 (FROM BRAKE SYSTEM MODULE) MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1958-83 | IMPLAUSIBILE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BSM_YRS_DATA INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1960-83 | MESSAGE COUNTER/CRC FAULT IN ENGINE1 (FROM ENGINE CONTROL MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1962-83 | MESSAGE COUNTER/CRC FAULT IN ENGINE3 - FROM ENGINE CONTROL MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1964-83 | MESSAGE COUNTER/CRC FAULT IN ENGINE4 - FROM ENGINE CONTROL MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1966-83 | MESSAGE COUNTER/CRC FAULT IN GE MESSAGE - FROM BODY COMPUTER MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U196E-83 | MESSAGE COUNTER/CRC FAULT IN MOT TRANSM2 - FROM ENGINE CONTROL MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1970-83 | MESSAGE COUNTER/CRC FAULT IN MOT TRANSM3 (FROM ENGINE CONTROL MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1978-83 | MESSAGE COUNTER/CRC FAULT IN STATUS EPB - FROM BRAKE SYSTEM MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U197A-83 | IMPLAUSIBILE DATA RECEIVED FROM DUAL CLUTCH TRANSMISSION MODULE CAN MESSAGE TRANSM1-VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U197C-83 | IMPLAUSIBILE DATA RECEIVED FROM DUAL CLUTCH TRANSMISSION MODULE CAN MESSAGE TRANSM2-VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1982-83 | MESSAGE COUNTER/CRC FAULT IN WHEEL INFO (FROM BRAKE SYSTEM MODULE) MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1984-83 | MESSAGE COUNTER/CRC FAULT IN WHEEL SPEED (FROM BRAKE SYSTEM MODULE) MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1986-83 | MESSAGE COUNTER/CRC FAULT IN SCCM CRS CTRL - FROM STEERING COLUMN CONTROL MODULE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U198A-83 | MESSAGE COUNTER/CRC FAULT IN BRAKE 7 (FROM BRAKE SYSTEM MODULE) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U19B0-83 | MESSAGE COUNTER/CRC FAULT IN BRAKE11 - FROM BRAKE SYSTEM MODULE - MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |