1.8L - Turbo Fuel Injection & Ignition, Engine Code(S): AWP
- 01 On Board Diagnostic (OBD)
- 24 Multiport Fuel Injection (MFI)
- Injection system, servicing
- Safety precautions
- Rules of cleanliness
- Technical data
- Component locations overview
- Notes
- Installation location of recirculating valve for turbocharger -N249- and Secondary Air Injection (AIR) solenoid valve -N112-
- Installation location of accelerator position senders -G79- and -G185-
- Installation location of oxygen sensors and connector cover
- Color coding of oxygen sensor connectors
- Installation locations of 3-pin connectors
- Installation location of brake light switch -F- and brake pedal switch (cruise control/diesel direct fuel injection -F47-
- Installation location of clutch vacuum vent valve switch -F36-
- Installation location of pressure switch/power steering -F88-
- Installation location of Motronic Engine Control Module (ECM) Power Supply Relay -J271- and Secondary Air Injection (AIR) Pump Relay -J299-
- Air cleaner, disassembling and assembling
- Wiring and component check using test box VAG 1598/31
- Procedure after voltage supply open circuit
- Engine Control Module (ECM) (without metal anti-theft housing), replacing
- Engine Control Module (ECM) (with metal anti-theft housing), replacing
- Idle speed, testing
- System pressure, fuel pressure regulator and holding pressure, checking
- Fuel injectors, testing
- Fuel rail with injectors, disassembling and assembling
- Fuel injectors, removing and installing
- Fuel injector leakage, injection quantity and spray pattern, checking
- Fuel Pump (FP) Relay -J17-, testing and activating
- Mass Air Flow (MAF) sensor -G70-, testing
- Intake air system, checking for leaks (unmetered air)
- Oxygen sensor control, testing
- Oxygen sensor and oxygen sensor control (before catalytic converter), testing
- Oxygen sensor aging (before catalytic converter) testing
- Oxygen Sensor (O2S) Heater -Z19- (before catalytic converter), testing
- Oxygen sensor and oxygen sensor control (after catalytic converter), testing
- Oxygen sensor (O2S) heater 1 -Z29- (after catalytic converter), testing
- Oxygen sensor, removing and installing
- Evaporative emission (EVAP) canister purge regulator valve, testing
- Electronic engine power control (electronic throttle), testing
- Operation of electronic throttle system
- Electronic throttle warning lamp in instrument cluster
- Electronic Power Control (EPC) warning lamp -K132-, testing
- Throttle valve control module -J338-, testing
- Throttle valve control module, adaptation
- Throttle valve, checking for soiling
- Throttle valve control module, cleaning
- Angle sensors for throttle drive, testing
- Accelerator position sensors, testing
- Brake light switch and brake pedal position switch, testing
- Clutch vacuum vent valve switch -F36-, testing
- Auxiliary signals, testing
- Auxiliary signals, testing
- Engine speed (RPM) signal, checking
- Vehicle speed signal, testing
- Air conditioner compressor shut-off, testing
- Pressure switch/power steering -F88-, testing
- Crash signal wiring, testing
- Fuel consumption signal for on-board computer, testing
- Fuel level signal wiring, testing
- Data exchange between engine control module and other control modules with CAN-bus interface, testing
- Vacuum system layout
- Injection system, servicing
- 28 Ignition/Glow plug system
- Ignition system, testing
- General notes on ignition system
- Safety precautions
- Technical data
- Ignition coils with power output stages, testing
- Motronic Engine Control Module (ECM) power supply relay -J271-, testing
- Intake air temperature (IAT) sensor -G42-, testing
- Engine speed (RPM) sensor -G28-, testing
- Engine coolant temperature (ECT) sensor -G62-, testing
- Voltage supply for control module, testing
- Knock sensor control limit, testing
- Knock sensors, testing
- Camshaft Position (CMP) sensor -G40-, testing
- Misfiring recognition, checking
- Ignition system, testing