Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | R1234yf WORKING WITH A/C SERVICE STATION (1 OF 2) and WORKING WITH A/C SERVICE STATION (2 OF 2) R134a 87 AIR CONDITIONING (1 OF 2) and 87 AIR CONDITIONING (2 OF 2) |
||
| Torque | OVERVIEW - A/C COMPRESSOR POWER UNIT | ||
| Axle Nut/Hub Nut | |||
| Front | 200 Nm +180° | ||
| Rear | 200 Nm +180° | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC SYSTEM, BLEEDING |
||
| Disc Brakes | TECHNICAL DATA, BRAKES | ||
| Torque | OVERVIEW - FRONT BRAKES OVERVIEW - REAR BRAKES |
||
| Charging | |||
| Generator | N/A | ||
| Torque | |||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT, REMOVING AND INSTALLING
For engine code CYMC RIBBED BELT, REMOVING AND INSTALLING For engine code DPAA |
||
| 3.0 | RIBBED BELT, REMOVING AND INSTALLING | ||
| Belt Routing | |||
| 2.0L | Vehicles with Generator, See fig. 2 under OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE, VEHICLES WITH GENERATOR
For engine code CYMC Vehicles with Starter Generator, See fig 5 under OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE, VEHICLES WITH STARTER GENERATOR For engine code CYMC See figure 1 under OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE For engine code DPAA |
||
| 3.0L | Refer to the appropriate procedure in RIBBED BELT, REMOVING AND INSTALLING | ||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | COOLING SYSTEM, CHECKING FOR LEAKS
For engine code CYMC COOLING SYSTEM, CHECKING FOR LEAKS For engine code DPAA |
||
| 3.0L | COOLING SYSTEM, CHECKING FOR LEAKS | ||
| Thermostat R & I | |||
| 2.0L | OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT
For engine code CYMC OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT For engine code DPAA |
||
| 3.0L | OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | COOLANT PUMP, REMOVING AND INSTALLING
For engine code CYMC COOLANT PUMP, REMOVING AND INSTALLING For engine code DPAA |
||
| 3.0L | COOLANT PUMP, REMOVING AND INSTALLING | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION, CHECKING
For engine code CYMC COMPRESSION, CHECKING For engine code DPAA |
||
| Oil Pressure | OIL PRESSURE, CHECKING
For engine code CYMC OIL PRESSURE, CHECKING For engine code DPAA |
||
| Engine Oil Drain Plug | 30Nm | ||
| Overhaul | CYMC 10 ENGINE ASSEMBLY 13 CRANKSHAFT, CYLINDER BLOCK 15 CYLINDER HEAD, VALVETRAIN DPAA 10 ENGINE ASSEMBLY 13 CRANKSHAFT, CYLINDER BLOCK 15 CYLINDER HEAD, VALVETRAIN |
||
| Torque | CYMC Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN DPAA Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN |
||
| 3.0L | |||
| compression | COMPRESSION, CHECKING | ||
| Oil Pressure | OIL PRESSURE, CHECKING | ||
| Engine Oil Drain Plug | 30Nm | ||
| Overhaul | 10 ENGINE ASSEMBLY 13 CRANKSHAFT, CYLINDER BLOCK 15 CYLINDER HEAD, VALVETRAIN |
||
| Torque | Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | 60 Nm + 90° turn | ||
| Fuel System | |||
| Fuel Pressure Test Procedure | |||
| 2.0L/3.0L | TRANSFER FUEL PUMP -G6-, CHECKING | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L/3.0l | SPARK PLUGS, REPLACING | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | OVERVIEW - STARTER | ||
| Wheel Alignment | |||
| Adjustment Specifications | AXLE ALIGNMENT | ||
| Torque | Refer to the appropriate procedure in: 40 FRONT SUSPENSION 42 REAR SUSPENSION |
||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | N/A | ||