31 12 Control Arms and Struts
WARNING: This page is about a different car, the 2010 BMW 550i, 2009 BMW 550i, and 2008 BMW 550i. However, it is still accessible from the selected car via links, so may be relevant.
CONTROL ARMS AND STRUTS - TIGHTENING TORQUE SPECIFICATION
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Tension strut to front axle support | E12, E24 / until 5.82 | tighten in normal position | 80 Nm | |
| E23 | tighten in normal position | 135 Nm | ||
| E39, E52 | tighten in normal position | 110 Nm | ||
| E53 | Replace screw tighten in normal position | 165 Nm | ||
| E60, E61, E63, E64, E65, E66, E67 | M12 10.9 | Replace screw & nut tighten in normal position | ||
| Jointing torque | 100 Nm | |||
| Torque angle | 90 ° | |||
| E83 | Replace screw tighten in normal position | |||
| Jointing torque | 165 Nm | |||
| Torque angle | 90 ° | |||
| 2AZ Control arm to front axle support | E24 / from 5.82, E28, E31, E32, E34, E38, E39 / 8 cyl. | tighten in normal position | 77.5 Nm | |
| E39 / 6 cyl., E52 | tighten in normal position | 110 Nm | ||
| E12, E21, E23, E24 / until 5.82 | tighten in normal position | 85 Nm | ||
| E53, E60, E61, E63, E64, E65, E66, E67, E83 | M12 10.9 | Replace screw & nut tighten in normal position | ||
| Jointing torque | 100 Nm | |||
| Torque angle | 90±15 ° | |||
| 3AZ Control arm (ball joint) on front axle support | E30 | Replace nut | 85 Nm | |
| E36, E46 | Replace nut | 90 Nm | ||
| E30 / Four Wheel Drive | Replace nut | 100 Nm | ||
| E85, E86 | M14x1.5 | Replace nut | 80 Nm | |
| 4AZ Control arm to spring strut | E21, E30 | 65 Nm | ||
| 5AZ Control arm to pivot mount/spring strut | E30 / Four Wheel Drive | 85 Nm | ||
| E30 / Four Wheel Drive | Polystop nut | 93 Nm | ||
| E34 / Four Wheel Drive | 80 Nm | |||
| 6AZ Control arm on steering knuckle/swivel bearing | E36, E46, E85, E86 | Use of impact screwdriver not permitted! Replace nut | 65 Nm | |
| E38 | Replace nut | 93 Nm | ||
| E39, E53, E52, E83, E60 / Four Wheel Drive, E61 / Four Wheel Drive, E67 | Replace nut | 80 Nm | ||
| E60 / REAR END, E61 / REAR END, E63, E64, E65, E66 | Replace nut | 165 Nm | ||
| 7AZ Bracket for control arm to engine carrier | E30 | 42 Nm | ||
| E36 | 47 Nm | |||
| E46 | Replace screws | 59 Nm | ||
| E85, E86 | M10 10.9 | Replace screws | 56 Nm | |
| 8AZ Ball joint for control arm to front axle carrier | E34 / Four Wheel Drive, E46 / Four Wheel Drive | 77 Nm | ||
| 9AZ Control arm to ball joint | E34 / Four Wheel Drive, E46 / Four Wheel Drive | 80 Nm | ||
| 10AZ Control arm holder to front axle support | E34 / Four Wheel Drive | 47 Nm | ||
| E46 / Four Wheel Drive | Replace screws | 59 Nm | ||
| 11AZ Pressure strut to body | E24 / from 5.82, E28 | tighten in normal position | 130 Nm | |
| 12AZ Traction strut on tie rod lever/steering knuckle/swivel bearing | E24, E28 / from 5.82, E31, E32, E34, E38 | 93 Nm | ||
| E39 | 80 Nm | |||
| 13AZ Pressure strut to connecting pipe/front axle support | E31, E32, E34, E38, E39 | tighten in normal position | 127 Nm | |
| 14AZ Pressure strut to cruciform reinforcement | E31 | tighten in normal position | 127 Nm | |
| 15AZ Connecting pipe to body | E31, E32, E34 | 127 Nm | ||
| 16AZ Connecting pipe support to body | E31, E32, E34 | 59 Nm | ||
| 17AZ Connecting pipe to trailing spring mount | E24 / from 5.82, E28 | 60 Nm | ||
| 18AZ Leading strut to tie rod arm | E23 | 85 Nm | ||
| 19AZ Tension strut on steering knuckle/swivel bearing | E39, E52, E67 | 80 Nm | ||
| E60 / REAR END, E61 / REAR END, E63, E64, E65, E66 | 165 Nm | |||
| 20AZ Tension strut to guide joint | E53, E83 | Replace nut | 80 Nm | |
| E60 / Four Wheel Drive, E61 / Four Wheel Drive | Replace nut | 165 Nm | ||
| 21AZ Guide joint to swivel bearing | E53, E60 / Four Wheel Drive, E61 / Four Wheel Drive, E83 | Replace screws | 60 Nm |