Scan Tool Data Definitions

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2004 GMC Yukon XL, 2004 GMC Yukon, 2004 Chevrolet Tahoe, 2004 Chevrolet Suburban, and 2004 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.

8-Digit GM Part Number: The scan tool displays an 8 digit alphanumeric number. The part number of the module.
Amp Type: The scan tool displays the type of amplifier installed in the vehicle, Bose/Non-Bose.
Antenna Enable: The scan tool displays Active/Inactive.
Audio Device: The scan tool displays Null/Tuner/CD Player. The radio detects the presence of the device that is operating.
Balance: The scan tool displays -50 to +50. The Balance between the right and left audio output.
Bass: The scan tool displays 0-100%. The percentage of bass selected at the radio.
Battery Voltage: The scan tool displays 0-18 Volts. The Voltage measured from the radio or amplifier's ignition positive voltage circuit to ground.
Cal. Module 1 Part No.: The scan tool displays the 8 digit part number of the module.
Cal. Module 1 Suffix: The scan tool displays the 2 position suffix of the module.
CD Changer: The scan tool displays Connected if a CD changer is detected or Not Connected if no CD changer is present.
CD Changer Disc Number: The scan tool displays which CD the changer is currently playing.
CD Changer Track Number: The scan tool displays the track number of the disc that is currently playing.
CD Inserted: The scan tool displays Yes or No. Whether a CD is loaded or not.
Chime Type: The scan tool displays the type of chime select such as fast.
Chime Speaker: The scan tool displays Front Left, Front Right, LF Woofer, Back Left, Back Right, RF Woofer. The selected chime speaker is displayed
Chime Volume: The scan tool displays 0-100%. The percentage at which the chime volume has been calibrated to.
Component Serial Number: The scan tool displays the serial number of the module.
Day: The scan tool displays the day the software was created.
Digital Radio Antenna: This parameter indicates the amount of current being used by the digital radio antenna by measuring the voltage drop across an internal resistor. Early design modules support the mV reading while later design modules support a mA reading.
External Audio Device: The scan tool displays Connected/Not Connected. The radio senses the presence of an external audio device.
Fade: The scan tool displays -50 to +50. The Fade between the front and rear audio output.
Ignition Counter: The scan tool displays the number of ignition cycles.
Ignition Since Current DTC: The scan tool displays 0-225 Cycles. The number of ignition cycles since a current DTC was set.
Microphone Level: The scan tool displays 0-100%. The percentage of microphone selected at the radio.
Midrange: The scan tool displays 0-100%. The percentage of midrange selected at the radio.
Month: The scan tool displays the month the software was created. Mute
Noise Compensation: The scan tool displays On/Off. The selected switch position of the noise compensation system.
Operational S/W Part No.: The scan tool displays the 8 digit software part number of the module.
Operational S/W Suffix: The scan tool displays the 2 position software suffix of the module.
Personalization: The scan tool displays Driver 1/ Driver 2.
Phone: The scan tool displays whether or not a phone is present or not present.
Power Mode: The scan tool displays what power mode the module is on.
Radio ID: The scan tool displays the radio ID of the digital radio receiver.
RSA: The scan tool displays Present/ Not Present. Present is displayed if rear seat entertainment control is installed in the vehicle.
Signal Strength: The scan tool displays 0-225 dB. The signal strength of the radio frequency.
Software Version: The scan tool displays the version of software.
Speed Compensated Volume: The scan tool displays Off/Low/Medium/High according to what the auto volume is set on the module.
Source: The scan tool displays Off/Tuner/ICDX/CD/Cassette.This data parameter indicates the source that is operating.
Theft Armed: The scan tool displays Learned VIN/No VIN. The Scan tool displays Learned VIN when the theft mode has been turned ON by recognizing a valid VIN #.
Theft Locked: The scan tool displays Locked/Unlocked. The scan tool displays locked when the radio receives the incorrect VIN number across Class 2 lines.
Treble: The scan tool displays 0-100%. The percentage of treble selected at the radio.
Volume: The scan tool displays 0-100%. The percentage of volume selected at the radio.
Year: The scan tool displays the year the software was created.