Scan Tool Data Definitions

The scan tool displays the part number of the module.

The scan tool displays 0-16 Volts. The voltage measured between the module's battery positive circuit and ground circuit.

The scan tool displays a 4-digit number. This number designates the calibration or program level used in the PROM.

The scan tool displays 0-127.5 amps. The amount of amps used during seat operation.

The scan tool displays Off/High/Low. When the heated seat is on, the scan tool will display the status signal from the rear integration module to the climate control panel as High or Low.

The scan tool displays On/Off. When the heated seat is on, the scan tool will display the status signal from the heated seat module to the rear integration module as On.

The scan tool displays Idle/Pressed. When the driver heated seat switch is pressed, the scan tool will momentarily display the switch input of the climate control panel as Pressed.

The scan tool displays 0-5.0 Volts or 0-255 A/D. The sensor potentiometer provides an analog voltage which varies directly with the seat front vertical position. High scan tool values (Volts or A/D) indicate that the seat front is in the up position and low values indicate that the seat front is in the down position.

The scan tool displays 0-5.0 Volts or 0-255 A/D. The sensor potentiometer provides an analog voltage which varies directly with the seat horizontal position. High scan tool values (Volts or A/D) indicate that the seat is in the forward position and low values indicate that the seat is in the rearward position.

The scan tool displays a 3-digit number. This number is the day of the year that the module was built.

The scan tool displays Disabled/Enable. During a pre-determined heavy loading condition, the driver information module (DIM) will send out a class 2 message to the rear integration module (RIM) that a load shed level 1 is in effect and the scan tool will display Enable.

The scan tool displays Disabled/Enable. During a pre-determined heavy loading condition, the driver information module (DIM) will send out a class 2 message to the rear integration module (RIM) that a load shed level 2 is in effect and the scan tool will display Enable.

The scan tool displays 0-5.0 Volts or 0-255 A/D. The sensor potentiometer provides an analog voltage which varies directly with the lumbar horizontal position. High scan tool values (Volts or A/D) indicate that the Lumbar is in the forward position and low values indicate that the lumbar is in the rearward position.

The scan tool displays Idle/Memory 1/memory 2/Exit. When a memory function switch is pressed, the scan tool will momentarily display the function as selected.

The scan tool displays Off/On. When the heated seat is ON, the scan tool will display the status signal from the heated seat module to the rear integration module (RIM) as On.

The scan tool displays Idle/Pressed. When the passenger heated seat switch is pressed, the scan tool will momentarily display the heated seat switch input of the climate control panel as Pressed.

The scan tool displays Off/High/Low. When the passenger heated seat switch is pressed, the scan tool will display the status signal from the rear integration module to the climate control panel as High or Low.

This is the state of the personalization option as it is stored in the Dash Integration Module (DIM). When the Personalization Option is selected, the scan tool displays the directions to activate or deactivate the personalization option. The asterisk beside the option indicates that the personalization option is activated. The personalization option is normally set to the activated state during assembly of the vehicle.

The scan tool displays a 4-digit number. This is the identification number of the PROM that is incorporated into the module.

The scan tool displays 0-5.0 Volts or 0-255 A/D. The sensor potentiometer provides an analog voltage which varies directly with the seat rear vertical position. High scan tool values (Volts or A/D) indicate that the seat rear vertical is in the up position and low values indicate that the seat rear vertical is in the down position.

The scan tool displays 0-5.0 Volts or 0-255 A/D. The sensor potentiometer provides an analog voltage which varies directly with the seat recline position. High scan tool values (Volts or A/D) indicate that the seat recline is in the froward position and low values indicate that the seat recline is in the rearward position.

The scan tool displays Inactive/Active. When the seat forward switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat forward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat horizontal motor in the forward direction.

The scan tool displays Inactive/Active. When the seat front down switch is activated the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat front down switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat front vertical motor in the down direction.

The scan tool displays Inactive/Active. When the seat front up switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat front up switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat front vertical motor in the up direction.

The scan tool displays Inactive/Active. When the seat lumbar forward switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat lumbar forward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the lumbar horizontal motor in the forward direction.

The scan tool displays Inactive/Active. When the seat lumbar rearward switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat lumbar rearward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the lumbar horizontal motor in the rearward direction.

The scan tool displays Inactive/Active. When the seat rear down switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat rear down switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat rear vertical motor in the down direction.

The scan tool displays Inactive/Active. When the seat rear up switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat rear up switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat rear vertical motor in the up direction.

The scan tool displays Inactive/Active. When the seat rearward switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat rearward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat horizontal motor in the rearward direction.

The scan tool displays Inactive/Active. When the seat recline forward switch is activated, the scan tool will momentarily display the switch input to the memory sear module as Active.

The scan tool displays Inactive/Active. When the seat recline forward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat recline motor in the forward direction.

The scan tool displays Inactive/Active. When the seat recline rearward switch is activated, the scan tool will momentarily display the switch input to the memory seat module as Active.

The scan tool displays Inactive/Active. When the seat recline rearward switch is activated or when a memory recall occurs, the scan tool will display Active while the output from the memory seat module is commanding the seat recline motor in the rearward direction.

The scan tool displays a 4-digit number. This number represents the year the module was built.