LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2003 >> Seville V8-4.6L VIN 9 >> Repair and Diagnosis >> Body and Frame >> Body Control Systems >> Testing and Inspection >> Scan Tool Testing and Procedures >> Scan Tool Data Definitions
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Scan Tool Data Definitions

SCAN TOOL DATA DEFINITIONS

8-Digit GM Part Number: The scan tool displays the module GM part number.

Battery Voltage: The scan tool displays 0-20 Volts. The scan tool displays the voltage as received on the battery positive voltage circuit of the Module or the 72-08 battery voltage message from the DIM over class serial data 2 line.

Calibration ID: The scan tool displays the Calibration ID number for service identification.

Component Serial #8-11: Digits 8 to 11 of the component serial number of the control module.

Component Serial #8-12: Digits 8 to 12 of the component serial number of the control module.

Component Serial #12: Digit 12 of the component serial number of the control module.

Component Serial #13-16: Digits 13 to 16 of the component serial number of the control module.

Component Serial #17-18: Digits 17 to 18 of the component serial number of the control module.

Ign. 3 Input: The scan tool displays Active/Inactive. Display indicates the state of the ignition 3 input.

Ign. Accessory: The scan tool displays Active/Inactive. Display indicates the state of the ignition accessory input.

Ign. Crank/Run: The scan tool displays Active/Inactive. Display indicates the state of the ignition crank/run input.

Ign. Off/Run/Crank: The scan tool displays Active/Inactive. Display indicates the state of the ignition Off/Run/Crank input.

Ign. Run: The scan tool displays Active/Inactive. Display indicates the state of the ignition run input.

Ignition Counter: The scan tool displays 0-255 counts. The module counts each time the ignition is cycled.

Ignition Crank: The scan tool displays Active/Inactive. The scan tool displays Active when the DIM receives a battery voltage signal from the ignition switch.

Ignition Cycle Counter: The scan tool displays 0-100. Display indicates the number of ignition cycles up to 100.

Ignition Switch: The scan tool displays Accy/Crank/Off/RAP/RAP-Unlock/Run/Unlock. The scan tool displays Accy when the accessory and unlock circuits of the DIM receives a battery voltage signal from the ignition switch. The scan tool displays Crank when the Crank/Run, Run and Unlock circuits of the DIM receives a battery voltage signal from the ignition switch. The scan tool displays Off when none of the power moding circuits of the DIM receive a battery voltage signal from the ignition switch. The scan tool displays RAP (Retained Accessory Power) when RAP is active and none of the power moding circuits of the DIM receive a battery voltage signal from the ignition switch. The scan tool displays RAP-Unlock when RAP is active and the Ign. Unlock circuit of the DIM receives a battery voltage signal from the ignition switch. The scan tool displays Run when all of the power moding circuits of the DIM receive a battery voltage signal from the ignition switch. The scan tool displays Unlock when the Unlock circuit of the DIM receives a battery voltage signal from the ignition switch.

PROM ID: The scan tool displays the module PROM ID.

Run/Crank: The scan tool displays On/Off. The scan tool displays On when the Run/Crank circuit of the IPM receives a battery voltage signal from the ignition switch.

Vehicle Speed: The scan tool displays 0-249 km/h (0-155 mph). This value is used to calculate the outside air temperature when the vehicle is moving.

Year Module Built: The scan tool displays the module year built.
scientia non olet · About LEMON Manuals