Scan Tool Output Controls
Electronic Brake Control Module (EBCM) Scan Tool Data Output Controls
| Scan Tool Output Control | Additional Menu Selection(s) | Description |
|---|---|---|
| ABS Failed Lamp Command | Normal Mode Eavesdrop / Phase 1-4 | Displays the status of the ABS indicator. |
| ABS Reference Speed | Normal Mode Eavesdrop / Phase 1-4 | Displays the vehicle speed from the average of all four wheel speeds. |
| Automated Bleed | - | Used to bleed the ABS hydraulics. Refer to ABS Automated Bleed Procedure . |
| Automated Test | - | Cycles each solenoid valve and the pump motor in order to verify component operation. This test is identical to the Initialization Sequence. If a malfunction is detected, the EBCM will set the appropriate DTCs. The DTCs will be displayed upon completion of the test. |
| CVRSS Equipped | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the vehicle is equipped with road sensing suspension. |
| Engine RPM | Normal Mode Eavesdrop / Phase 1-4 | Displays the crankshaft rotation speed. |
| Engine Type | Normal Mode Eavesdrop / Phase 1-4 | Displays the type of engine in the vehicle. |
| Estimated Trans. Gear | Normal Mode Eavesdrop / Phase 1-4 | Displays the estimated state of the transmission gear. |
| Extended Travel Brake Switch | Normal Mode Eavesdrop / Phase 1-4 | Displays the state of the extended travel brakes switch. |
| Intake Air Temperature | Normal Mode Eavesdrop / Phase 1-4 | Displays the temperature of the intake manifold air. |
| Lateral Acceleration | Normal Mode Eavesdrop / Phase 1-4 | Displays the lateral acceleration from the lateral accelerometer signal. |
| LF Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| LF Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| LF TCS Isolation Valve | Solenoid Test | Commands the solenoid ON and OFF. |
| LF TCS Prime Valve | Solenoid Test | Commands the solenoid ON and OFF. |
| LR Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| LR Valve Outlet Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| Normal Force Test | - | Ensures that the wires between the EBCM and electronic suspension control module are not crossed. A message is displayed indicating if the test is passed or if there is a malfunction. The test will not run if any EBCM or electronic suspension control module DTCs are set. |
| Normal Mode Eavesdrop | - | Monitors the serial data messages that relate to system operation. The normal mode eavesdrop is a list of data parameters. The normal mode eavesdrop function has the following 2 modes: Phase 1-4: The term phase refers to the ignition switch changing states. The data parameters shown will display a value only when there is a change in the ignition state. Otherwise, the scan tool displays all asterisks next to each parameter. No Phase: The data parameters shown are not affected by the changing of ignition states. The scan tool will display a value only when there is a serial data message that relates to the individual parameter. Otherwise, the scan tool displays all asterisks next to each parameter. |
| Powertrain TCS Failure | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the PCM has suspended TCS due to a malfunction related to TCS. |
| Pump Motor Test | - | Commands the pump motor ON and OFF. |
| Red Brake Warning Indicator | Normal Mode Eavesdrop / Phase 1-4 | Displays the status of the Red Brake Warning indicator. |
| RF Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| RF Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| RF TCS Isolation Valve | Solenoid Test | Commands the solenoid ON and OFF. |
| RF TCS Prime Valve | Solenoid Test | Commands the solenoid ON and OFF. |
| Rough Road Parameter | Normal Mode Eavesdrop / Phase 1-4 | Displays the EBCM calculation of the road surface. |
| RR Inlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| RR Outlet Valve Solenoid | Solenoid Test | Commands the solenoid ON and OFF. |
| Service Stability System | Normal Mode Eavesdrop / Phase 1-4 | Displays the status of the Service Stability System message. |
| Stability System Active | Normal Mode Eavesdrop / No Phase | Displays the active status of the VSES. |
| State of Health Present | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the EBCM is sending the proper state of health message. |
| Steering Position Sensor Test | - | Tests the steering wheel position sensor (SWPS) ability to provide a valid input. |
| Stop Lamp Switch | Normal Mode Eavesdrop / Phase 1-4 | Displays the current status of the brake switch. |
| Suspension Failure Status | Normal Mode Eavesdrop / No Phase | Displays the status of the road sensing suspension. |
| System Power Mode | Normal Mode Eavesdrop / Phase 1-4 | Displays the current state of the ignition as reported by the dash integration module (DIC). |
| TCC/Brake Switch Active | Normal Mode Eavesdrop / Phase 1-4 | Displays the status of the brake switch. |
| TCS Active Message Command | Normal Mode Eavesdrop / No Phase | Indicates if the EBCM is commanding the Traction Active indicator ON. |
| TCS Equipped | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the vehicle is equipped with TCS. |
| TCS Failed Lamp Command | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the EBCM is commanding the Traction Off indicator ON. |
| TCS Off Indicator/Message | Normal Mode Eavesdrop / No Phase | Displays the status of the Traction message. |
| TCS On/Off Switch | Normal Mode Eavesdrop / No Phase | Displays the state of the traction control switch. |
| TCS On/Off Test | - | Commands the traction control system ON and OFF. Performs the same function as the traction control switch. |
| TCS Test | - | Runs the pump motor in order to apply fluid pressure to the front wheel circuits. |
| Temporary Inhibit of TCS | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the EBCM has suspended the TCS due to a malfunction of the driver using the traction control switch. |
| TPS - Pedal Position | Normal Mode Eavesdrop / Phase 1-4 | Displays the percentage of throttle that is currently being applied. |
| Traction Ready Message Command | Normal Mode Eavesdrop / No Phase | Displays the status of the Traction Ready message. |
| Traction Suspended Message Comm. | Normal Mode Eavesdrop / No Phase | Displays the status of the Traction Suspended message. |
| Transmission Type | Normal Mode Eavesdrop / Phase 1-4 | Displays the type of transmission in the vehicle. |
| VIN Packet #2 | Normal Mode Eavesdrop / Phase 1-4 | Displays the VIN packet #2. |
| VSES Active | Normal Mode Eavesdrop / Phase 1-4 | Displays the current status of the VSES. |
| VSES Equipped | Normal Mode Eavesdrop / Phase 1-4 | Indicates if the vehicle is equipped with VSES. |