Specifications Index
DTS SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Driveshaft Axle Nut (FE1, FE3) | 118 ft. lbs. (160 N.m) | ||
| Driveshaft Axle Nut (FE7) | 170 ft. lbs. (230 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS (J55) DISC BRAKE COMPONENT SPECIFICATIONS (JL9) |
||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine Belt Is Not Adjustable | ||
| Belt Routing | See illustration under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 4.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 4.6L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 4.6L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - Minimum @ Idle 5 psi (35 kPa) Oil Pressure - Minimum @ 2,000 RPM 35 psi (250 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LD8) ENGINE MECHANICAL SPECIFICATIONS (L37) |
||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | First Pass 22 ft. lbs. (30 N.m) Final Pass + an additional 50 degrees |
||
| Fuel System | |||
| Pressure Specification | Commanded on using scan tool 55-61 psi (384-425 kPa) | ||
| Fuel Pressure Test Procedure | See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel strainer attaches to lower end of fuel sender | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 4.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 4.6L (Type = GM 12571535) | |||
| Gap | 0.050 in (1.27 mm) | ||
| Torque | Used Cylinder Head 11 ft. lbs. (15 N.m) New Cylinder Head 15 ft. lbs. (20 N.m) |
||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) | ||