LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2006 >> STS Base, 3.6 7, AWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - 3.6L - Introduction (2 Of 2) >> Repair Instructions >> Engine Control Module Replacement >> Removal Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal Procedure

    Fig 1: ECM Electrical Connector Lever Lock & Lock Slide
    GM1285259Courtesy of GENERAL MOTORS CORP.
  1. Turn the ignition OFF.
  2. Remove the front compartment sight shields as necessary. Refer to Front Compartment Sight Shields Replacement in Body Front End.
  3. Using a scan tool, retrieve the percentage of remaining engine oil and the remaining automatic transmission fluid life. Record the remaining engine oil and the remaining automatic transmission fluid life.
    4. IMPORTANT: Ensure that there is no main relay circuit voltage (ECM Fuse).
  4. Use a DMM in order to measure the main relay circuit voltage at the ECM fuse in the underhood fuse block. Refer to Electrical Center Identification Views in Wiring Systems.
  5. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  6. Remove the ECM fuse in the underhood fuse block. Refer to Electrical Center Identification Views in Wiring Systems.
  7. Remove the TCM/IPC fuse in the underhood fuse block. Refer to Electrical Center Identification Views in Wiring Systems.
  8. Remove the ECM/TCM fuse in the underhood fuse block. Refer to Electrical Center Identification Views in Wiring Systems.
  9. Unlock the chassis side (upper) engine control module (ECM) electrical connector.
    1. Depress the ECM electrical connector lever lock (1).
    2. Simultaneously rotate the ECM connector clamp lever and depress the lock slide (2).
    10. NOTE: In order to prevent any possible electrostatic discharge damage to the ECM, do not touch the connector pins.
    Fig 2: View Of Upper ECM Connector
    GM1343429Courtesy of GENERAL MOTORS CORP.
  10. Remove the body side (upper) ECM connector.
    11. Fig 3: View Of ECM Wiring Harness Connector
    GM945720Courtesy of GENERAL MOTORS CORP.
  11. Unlock and remove the engine side (lower) ECM connector.
    12. Fig 4: View Of ECM Redundant Ground Wire Bolt
    GM1343434Courtesy of GENERAL MOTORS CORP.
  12. Remove the ECM redundant ground wire and bolt (2) from the ECM.
    13. Fig 5: View Of ECM
    GM887860Courtesy of GENERAL MOTORS CORP.
  13. Remove the ECM bolts.
  14. Remove the ECM.
    15. Fig 6: View Of Engine Wiring Harness Bracket Bolt - Top Of ECM Bracket
    GM945521Courtesy of GENERAL MOTORS CORP.
  15. If you are replacing the ECM bracket, perform the following steps (16 through 20):
  16. Remove the electrical connector bracket and bolt from the ECM bracket.
    17. Fig 7: View Of ECM Ground Harness Terminal Screw
    GM945670Courtesy of GENERAL MOTORS CORP.
  17. Remove the ground wire and bolt from the ECM bracket.
    18. Fig 8: View Of Engine Wiring Harness Bracket Bolt - Side Of ECM Bracket
    GM945513Courtesy of GENERAL MOTORS CORP.
  18. Remove the wire harness retainer and bolt from the side of the ECM bracket.
    19. Fig 9: View Of ECM Bracket
    GM887861Courtesy of GENERAL MOTORS CORP.
  19. Remove the ECM bracket bolts (2 and 3).
  20. Remove the ECM bracket (1).
scientia non olet · About LEMON Manuals