Body Control Module (BCM)
- ALC Switch
-
The scan tool displays On/Off. When the ambient light level indicates low light level then the BCM will turn on the automatic light control (ALC) then the scan tool will display On.
- Backup Lamp Relay Command
-
The scan tool display On/Off. When the transmission is placed in the REVERSE position the scan tool displays On.
- BPP Sensor
-
The scan tool displays Volts. The varied voltage from the BPP sensor is displayed on the scan tool.
- BPP Sensor Learn Home Position
-
The scan tool displays Counts. The brake pedal home position is displayed as Counts.
- BPP Sensor Learn in Progress
-
The scan tool displays No/Yes. When the BPP Sensor is being reprogrammed, the scan tool displays Yes.
- BPP Sensor High During Learn
-
The scan tool displays No/Yes. If the BPP sensor is shorted high during reprogramming, the scan tool will display Yes.
- BPP Sensor Low During Learn
-
The scan tool displays No/Yes. If the BPP sensor is shorted low during reprogramming, the scan tool will display Yes.
- BPP Sensor Move During Learn
-
The scan tool displays No/Yes. If the BPP sensor is moved during reprogramming, the scan tool will display Yes.
- BPP Sensor Reference Signal
-
The scan tool displays Volts. The 5-volt reference voltage is displayed.
- BPP Sensor Status Unlearned
-
The scan tool displays No/Yes. If the BPP sensor is not programmed then the scan tool displays Yes.
- Day / Night Status
-
The scan tool displays Day/Night. When the daylight conditions are present the scan tool will display Day.
- DRL Status
-
The scan tool displays On/Off. When the ambient light level indicates daylight level then the scan tool will display ON.
- Flash to Pass Switch
-
The scan tool displays Inactive/Active. When Flash to Pass switch is placed in the OFF position, the scan tool displays Inactive.
- Fog Lamp Relay CMD
-
The scan tool displays On/Off. When the fog lamps are placed in the ON position then the scan tool displays On.
- Front Fog Lamp Switch
-
The scan tool displays Inactive/Active. When the fog lamp switch is in the OFF position the scan tool displays Off.
- Hazard Lamp Switch
-
The scan tool displays Inactive/Active. When the hazard switch is placed in the ON position, the scan tool will display ON.
- Headlamps OFF Switch
-
The scan tool displays On/Off. When the headlamp switch is placed in the OFF position, the scan tool displays On.
- Headlamps ON Switch
-
The scan tool displays Inactive/Active. When the headlamp switch is placed in the ON position, the scan tool displays Active.
- High Beam Relay Command
-
The scan tool displays On/Off. When the high beam headlamps are turned on, the scan tool displays On.
- High Beam Select Switch
-
The scan tool displays Inactive/Active. When the high beam headlamps are turned on, the scan tool displays Active.
- IGN Mode Sw Dimming CMD
-
The scan tool displays On/Off. When the ignition switch dimming is commanded on, the scan tool displays On.
- Inadvert Power CMD
-
The scan tool displays On/Off. When the inadvertent power is being commanded on by the BCM the scan tool displays On.
- Inadvert Power Signal
-
The scan tool displays Inactive/Active. When the inadvertent power is being commanded on by the BCM the scan tool displays Active.
- Left Turn Signal Switch
-
The scan tool displays Inactive/Active. When the turn signal switch is placed in the LEFT position, the scan tool will display Active.
- LF Door Ajar Switch
-
The scan tool displays Closed/Open. When the LF door is opened, the scan tool displays Open.
- LF Turn / Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LF Turn Lamp / DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the LEFT position, scan tool displays On.
- Low Beam Relay Command
-
The scan tool displays On/Off. When the headlamp are turned on, the scan tool displays On.
- LR Turn / Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LR Turn Lamp / DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the LEFT position, scan tool displays On.
- Park Lamp Relay CMD
-
The scan tool displays On/Off. When the park lamps are turned on, the scan tool will display On.
- Park Lamp Switch
-
The scan tool displays On/Off. When the park lamp switch is placed in the ON position, the scan tool will display On.
- Rear Fog Lamp Relay CMD
-
The scan tool displays On/Off. When the rear fog lamps are placed in the ON position then the scan tool displays On.
- Rear Fog lamp Switch
-
The scan tool displays inactive / active. When the rear fog lamp switch is in the OFF position the scan tool displays Off.
- RF Door Ajar Switch
-
The scan tool displays Closed/Open. When the RF door is opened, the scan tool displays Open.
- RF Turn / Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the RIGHT position, the scan tool displays On.
- RF Turn Lamp / DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the RIGHT position, scan tool displays On.
- Right Turn Signal Switch
-
The scan tool displays Inactive/Active. When the turn signal switch is placed in the RIGHT position, the scan tool will display Active.
- RR Turn / Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the RIGHT position, the scan tool displays On.
- RR Turn Lamp / DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the RIGHT position, scan tool displays On.
- Stop Lamp Relay Command
-
The scan tool displays On/Off. When the brakes are applied, the scan tool displays On.
- Stop Lamp Status
-
The scan tool displays On/Off. When the stop lamps are applied, the scan tool displays On.
- Theater Dimming Command
-
The scan tool displays On/Off. When the theater dimming is commanded on by the BCM, the scan tool displays On.
- Trunk Release Switch
-
The scan tool displays Inactive/Active. When the trunk release switch is pressed, the scan tool displays Active.