Scan Tool Data Definitions

The scan tool displays an 8 digit alphanumeric number. The part number of the module.

This is the stopping level for the seek/scan feature when set to distant mode.

This is the stopping level for the seek/scan feature when set to local mode.

The scan tool displays On/Off. The state of the auto volume control function.

The scan tool displays 0-255 counts. The amount of left to right balance selected.

The scan tool displays AM/FM1/FM2. The current band that the radio is in.

The scan tool displays 0-255 counts. The amount of bass selected.

The scan tool displays 0-25.5 volts. The voltage measured from the modules battery positive voltage circuit to the modules ground circuit.

The scan tool displays the sequence of build of the radio.

The scan tool displays 0-9999. The number designating what calibrations the radio contains.

The scan tool displays Connected/Not Connected. This indicates the presence of a CD changer.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays 0-99. The number designates the current channel selected.

The scan tool displays 12 Hr or 24 Hr.

The scan tool displays the serial number of the module.

The scan tool displays 0-9. The second portion of the serial number.

The scan tool displays 0-9999. The first portion of the serial number.

The scan tool displays the day the software was created.

This parameter indicates the amount of current being used by the digital radio antenna by measuring the voltage drop across an internal resistor. Early design modules support the mV reading while later design modules support a mA reading.

The scan tool displays the equalization setting selected (talk, front/driver seat, ambience, spacious, or off).

The scan tool displays Driver 1/Driver 2. The memory position the driver has selected as received by class 2 lines.

The scan tool displays 0-255 counts. The amount of front to rear fade selected.

This is the stopping level for the seek/scan feature when set to distant mode.

This is the stopping level for the seek/scan feature when set to local mode.

The scan tool displays the number of ignition cycles.

The scan tool displays the number of ignition cycles since the last DTC was set.

The scan tool displays the current language displayed on the radio.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays Present/Not Present. This parameter displays the ability to receive long wave RF signals.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays the shift information for the build of the radio.

The scan tool displays the site code where the unit was manufactured.

The scan tool displays 0-255 counts. The amount of noise measured in the vehicle. This is the higher of two measurements. Once Microphone Low has reached the limit, noise is then measured in Microphone High.

The scan tool displays 0-255 counts. The amount of noise measured in the vehicle. This is the lower of two measurements. Once this has reached the limit, noise is then measured in Microphone High.

The scan tool displays 0-255 counts. The amount of mid range selected.

The scan tool displays 0-99 counts. The volume selected for the phone output.

The scan tool displays the month the software was created.

The scan tool displays On/Off indicating the state of the mute button.

The scan tool displays 0-99. The number of times a new VIN number has been set in the radio.

The scan tool displays if the phone is Active/Inactive.

The scan tool displays the country the vehicle was sold in.

The scan tool displays the current power mode the module is operating in.

The scan tool displays Home/Away. This is the current radio preset setting.

The scan tool displays 0-9999. The identification number of the radios internal PROM.

The scan tool displays 0-9999. The identification number of the radio internal PROM.

The scan tool displays 0-9999. The identification number of the navigation internal PROM.

The scan tool displays the version of software of the radio.

The scan tool displays the radio ID of the digital radio receiver.

The scan tool displays On/Off. The state of the amplifier input.

The scan tool displays On/Off. The state of the amplifier input.

The scan tool displays what level radio is currently installed in the vehicle.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays the region the radio is set for.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays On/Off. The state of the speaker output.

The scan tool displays 0-255 decibels. The strength of the radio station that the radio is tuned to.

The scan tool displays 0-255 decibels. The strength of the TV station that the radio is tuned to.

The scan tool displays which source has been selected (Tuner, CDX, Phone, Off).

The scan tool displays Learned VIN/No VIN. The Scan tool displays Learned VIN when the theft mode has been turned ON by recognizing a valid VIN.

The scan tool displays Active/Inactive. The scan tool displays Active when the radio receives the incorrect VIN.

The scan tool displays ON or OFF. The state of the chime.

The scan tool displays 0-999 hrs. The total number of hours the single CD has been used.

The scan tool displays 0-999 hrs. The total number of hours the CD changer has been used.

The scan tool displays 0-999 hrs. The total number of hours the radio has been used.

The scan tool displays 0-255 counts. The amount of treble selected.

The scan tool displays 0-255 counts. The volume selected.

The scan tool displays the year the software was created.