Body Control Module (BCM)
- ALC Switch
-
The scan tool displays On/Off. When the ambient light level indicates low light level then the BCM will turn on the automatic light control (ALC) then the scan tool will display On.
- Backup Lamp Relay Cmd.
-
The scan tool display On/Off. When the transmission is placed in the REVERSE position the scan tool displays On.
- Battery Voltage Signal
-
The scan tool displays Volts. This is the current battery voltage at the BCM.
- BPP Sensor
-
The scan tool displays Volts. The varied voltage from the BPP sensor is displayed on the scan tool.
- BPPS Learn Home Position
-
The scan tool displays Counts. The brake pedal home position is displayed as Counts.
- BPPS High During Learn
-
The scan tool displays No/Yes. If the BPP sensor is shorted high during reprogramming, the scan tool will display Yes.
- BPPS Low During Learn
-
The scan tool displays No/Yes. If the BPP sensor is shorted low during reprogramming, the scan tool will display Yes.
- BPPS Move During Learn
-
The scan tool displays No/Yes. If the BPP sensor is moved during reprogramming, the scan tool will display Yes.
- BPP Sensor Reference
-
The scan tool displays Volts. The 5-volt reference voltage is displayed.
- BPPS Status
-
The scan tool displays Learned/Unlearned. If the BPP sensor is not programmed then the scan tool displays Unlearned.
- Day/Night Status
-
The scan tool displays Off/On. When the daylight conditions are present the scan tool will display Off.
- DRL Status
-
The scan tool displays On/Off. When the ambient light level indicates daylight level then the scan tool will display ON.
- Flash to Pass Switch
-
The scan tool displays Inactive/Active. When Flash to Pass switch is placed in the OFF position, the scan tool displays Inactive.
- Fog Lamp Relay Cmd.
-
The scan tool displays On/Off. When the fog lamps are placed in the ON position then the scan tool displays On.
- Front Fog Lamp Switch
-
The scan tool displays Inactive/Active. When the fog lamp switch is in the OFF position the scan tool displays Off.
- Hazard Lamp Switch
-
The scan tool displays Inactive/Active. When the hazard switch is placed in the ON position, the scan tool will display ON.
- Headlamp OFF Switch
-
The scan tool displays On/Off. When the headlamp switch is placed in the OFF position, the scan tool displays On.
- Headlamp ON Switch
-
The scan tool displays Inactive/Active. When the headlamp switch is placed in the ON position, the scan tool displays Active.
- High Beam Relay Command
-
The scan tool displays On/Off. When the high beam headlamps are turned on, the scan tool displays On.
- High Beam Select Switch
-
The scan tool displays Inactive/Active. When the high beam headlamps are turned on, the scan tool displays Active.
- Ign. Mode Sw. Dimming Command
-
The scan tool displays On/Off. When the ignition switch dimming is commanded on, the scan tool displays On.
- Inadvertent Power Cmd.
-
The scan tool displays On/Off. When the inadvertent power is being commanded on by the BCM the scan tool displays On.
- Inadvertent Power Signal
-
The scan tool displays Inactive/Active. When the inadvertent power is being commanded on by the BCM the scan tool displays Active.
- Learn in Progress
-
The scan tool displays No/Yes. When the BPP Sensor is being reprogrammed, the scan tool displays Yes.
- Left Turn Signal Switch
-
The scan tool displays Inactive/Active. When the turn signal switch is placed in the LEFT position, the scan tool will display Active.
- LF Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LF Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the LEFT position, scan tool displays On.
- Low Beam Relay Command
-
The scan tool displays On/Off. When the headlamp are turned on, the scan tool displays On.
- LR Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LR Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the LEFT position, scan tool displays On.
- Park Lamp Relay Cmd.
-
The scan tool displays On/Off. When the park lamps are turned on, the scan tool will display On.
- Park Lamp Switch
-
The scan tool displays On/Off. When the park lamp switch is placed in the ON position, the scan tool will display On.
- Rear Fog Lamp Relay Cmd.
-
The scan tool displays On/Off. When the rear fog lamps are placed in the ON position then the scan tool displays On.
- Rear Fog lamp Switch
-
The scan tool displays inactive/active. When the rear fog lamp switch is in the OFF position the scan tool displays Off.
- RF Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the RIGHT position, the scan tool displays On.
- RF Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the RIGHT position, scan tool displays On.
- Right Turn Signal Switch
-
The scan tool displays Inactive/Active. When the turn signal switch is placed in the RIGHT position, the scan tool will display Active.
- RR Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the RIGHT position, the scan tool displays On.
- RR Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded on by the BCM or the turn signal switch is placed in the RIGHT position, scan tool displays On.
- Stop Lamp Relay Command
-
The scan tool displays On/Off. When the brakes are applied, the scan tool displays On.
- Stop Lamp Status
-
The scan tool displays On/Off. When the stop lamps are applied, the scan tool displays On.
- Theater Dimming Command
-
The scan tool displays On/Off. When the theater dimming is commanded on by the BCM, the scan tool displays On.