LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2009 >> Escalade EXT >> Repair and Diagnosis >> Accessories & Equipment >> Memory Modules >> Adjustable Pedal System >> Diagnostic Information and Procedures >> Adjustable Pedals Inoperative (without AN3) >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

  1. Ignition OFF, disconnect the X2 harness connector at the left IP junction block.
  2. Test for less than 10 ohms between the ground circuit terminal D1 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify the test lamp illuminates between the B+ circuit terminal E2 and ground.
    • If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal and the circuit fuse is open, test the motor control circuits and the switch control circuits for a short to ground.
  4. Transmission in reverse, verify that a test lamp illuminates between the control circuit terminal E3 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
  5. Ignition OFF, connect the X2 harness connector at the left IP junction block and disconnect the harness connector at the adjustable pedal switch.
  6. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 11 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the left IP junction block.
  7. Ignition OFF, connect the harness connector at the adjustable pedal switch and disconnect the X2 harness at the left IP junction block.
  8. Ignition ON, verify a test lamp does not illuminate between the control circuit terminals listed below and ground:
    • Control circuit terminal E1
    • Control circuit terminal G1
    • If the test lamp illuminates, test the control circuit for a short to voltage. If the circuit tests normal, test or replace the adjustable pedal switch.
  9. Adjustable pedal switch in the FWD position, verify a test lamp illuminates between the control circuit terminal G1 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the adjustable pedal switch.
  10. Adjustable pedal switch in the RWD position, verify a test lamp illuminates between the control circuit terminal E1 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the adjustable pedal switch.
  11. Ignition OFF, connect the X2 harness connector at the left IP junction block and disconnect the harness connector at the adjustable pedal assembly.
  12. Test for less than 10 ohms between the control circuit terminals listed below and ground:
    • Control circuit terminal 4
    • Control circuit terminal 5
    • If greater than the specified range, test the control circuit for an open/high resistance. If the circuit tests normal, replace the left IP junction block.
  13. Ignition ON, verify a test lamp does not illuminate between the control circuit terminals listed below and ground:
    • Control circuit terminal 4
    • Control circuit terminal 5
    • If the test lamp illuminates, test the control circuit for a short to voltage. If the circuit tests normal, replace the left IP junction block.
  14. Adjustable pedal switch in the FWD position, verify a test lamp illuminates between the control circuit terminal 5 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground. If the circuit tests normal, replace the left IP junction block.
  15. Adjustable pedal switch in the RWD position, verify a test lamp illuminates between the control circuit terminal 4 and ground.
    • If the test lamp does not illuminate, test the control circuit for a short to ground. If the circuit tests normal, replace the left IP junction block.
  16. If all circuits test normal, test or replace the adjustable pedal assembly.
scientia non olet · About LEMON Manuals