LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2009 >> STS V >> Repair and Diagnosis >> Steering >> Power Steering System >> Repair Instructions >> Steering Gear Replacement >> Removal Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal Procedure

    Fig 1: Identifying J 42640
    GM333146Courtesy of GENERAL MOTORS CORP.
    CAUTION: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock, or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
    • The steering column
    • The intermediate shaft(s)
    • The steering gear

    After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has became un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.

  1. Install the J 42640  to the steering column.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Remove the front tires and wheels. Refer to Tire and Wheel Removal and Installation .
  4. If necessary in order to access the steering gear, remove the front air deflector. Refer toFront Air Deflector Replacement .
    5. Fig 2: View Of Intermediate Shaft Lower Pinch Bolt
    GM907425Courtesy of GENERAL MOTORS CORP.
    WARNING: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage may cause loss of steering control which could result in an accident and possible personal injury.
  5. Remove the left side engine splash shield. Refer to
  6. Remove the intermediate shaft lower pinch bolt.
  7. Disconnect the intermediate shaft from the power steering gear.
    8. Fig 3: View Of Variable Effort Steering Electrical Connector
    GM909110Courtesy of GENERAL MOTORS CORP.
  8. Disconnect the variable effort steering harness connector.
    9. Fig 4: View Of Outer Tie Rod Retaining Nuts
    GM886244Courtesy of GENERAL MOTORS CORP.
  9. Remove the outer tie rod retaining nuts.
    10. Fig 5: View Of Outer Tie Rod Assembly & J 24319-B
    GM643351Courtesy of GENERAL MOTORS CORP.
  10. Using the J 24319-B  , separate the outer tie rod from the steering knuckles.
  11. Place a drain pan under the vehicle.
    12. Fig 6: View Of Power Steering Gear Inlet Hose-To-Power Steering Gear Retaining Bolt
    GM1301495Courtesy of GENERAL MOTORS CORP.
  12. Remove the power steering hoses to power steering gear retaining bolt.
    13. Fig 7: View Of Power Steering Gear And Hoses
    GM908682Courtesy of GENERAL MOTORS CORP.
  13. Remove the power steering hoses (1, 3) from the power steering gear.
  14. If equipped with AWD, perform the following steps:
    1. Use a suitable jack in order to support the bottom of the front differential housing.
      2. Fig 8: Engine Mount Retaining Nuts
      GM1067552Courtesy of GENERAL MOTORS CORP.
    2. Loosen the right engine mount nut.
    3. Raise the differential housing in order to clear the steering rack bolt.
    15. Fig 9: Power Steering Gear Mounting Bolts
    GM874631Courtesy of GENERAL MOTORS CORP.
  15. Remove the power steering gear mounting bolts.
  16. If equipped with the 4.6L V8 (LH2) engine and all wheel drive (AWD), perform the following steps:
    1. Disconnect the left brake pipe from the brake hose.
    2. Plug the brake pipe.
    3. Carefully position the brake pipe to the side.
    4. Remove the nut and the bolt that retain the rear of the left front lower control arm to the frame.
  17. Remove the power steering gear through the left wheel opening.
scientia non olet · About LEMON Manuals