Folding Top Control Module Scan Tool Information

Folding Top Module Scan Tool Data Parameters

Parameter	System State	Expected Value	Description
Operating Conditions: Ignition ON
Battery Voltage Signal	-	Varies	This displays Volts. This is the current battery voltage signal.
Deck Lid Ajar Status	-	Deck Closed / Known	The scan tool displays Deck Ajar/Deck Closed or Known/Unknown. This is the state of the deck lid ajar switch.
Deck Lid Extended	-	Inactive	The scan tool displays Active or Inactive. This is the state of the deck lid.
Deck Lid Latch Status	-	Cleared	The scan tool displays Cleared or Not Cleared. This is the state of the deck lid latch.
Deck Lid Latch Switch	-	Deck Closed	The scan tool displays Deck Open or Deck Closed. This is the state of the deck lid latch switch.
Driver Window Operation	-	Varies	The scan tool displays Enabled or Disabled. This is the current state of the driver window system operation.
Folding Top Calibrated	-	Yes	The scan tool displays Yes or No. Yes is displayed if the folding top is calibrated properly.
Folding Top Close Reference Position	-	Varies	This displays Counts. This is the close reference position of the folding top measured in counts.
Folding Top Open Reference Position	-	Varies	This displays Counts. This is the open reference position of the folding top measured in counts.
Folding Top Position Sensor	-	Varies	This displays Counts. This is the position of the folding top measured in counts.
Folding Top Status	-	Varies	The scan tool displays Invalid, Retracted, Extended or Mid. This is the state of the folding top.
Front Tonneau Close Reference Position	-	Varies	This displays Counts. This is the close reference position of the front tonneau measured in counts.
Front Tonneau Open Reference Position	-	Varies	This displays Counts. This is the open reference position of the front tonneau measured in counts.
Front Tonneau Position Sensor	-	Varies	This displays Counts. This is the position of the front tonneau measured in counts.
Front Tonneau Status	-	Tonneau Closed	The scan tool displays Tonneau Open, Tonneau Closed or Mid. This is the state of the front tonneau.
Header Latch Limit Switches	-	Latched	The scan tool displays Invalid, Latched, Unlatched or Mid. This is the state of the header latch limit switches.
Left Front Window Status	-	OK	The scan tool displays OK or Out Of Limit. This is the state of the left front window.
Limit Switch Supply Voltage	-	Present	The scan tool displays Present or Not Present. This is the state of the limit switch supply voltage.
Luggage Barrier In Place	-	Yes	The scan tool displays Yes or No. Yes is displayed if the luggage barrier is in place.
Luggage Barrier Limit Switch	-	Varies	The scan tool displays Open or Closed. This is the state of the luggage barrier limit switch.
Motor Command	-	Varies	This displays amps.
Motor Feedback Current	-	OK	The scan tool displays OK or High. This is the state of the motor feedback.
Motor X Direction Command	-	Off	The scan tool displays On of Off. This is the state of motor X.
Motor Y Direction Command	-	Off	The scan tool displays On of Off. This is the state of motor Y.
Passenger Window Operation	-	Varies	The scan tool displays Enabled or Disabled. This is the current state of the passenger window system operation.
Passenger Window Position Status	-	OK	The scan tool displays OK or Out Of Limit. This is the state of the passenger window.
Position Sensors Status	-	OK	The scan tool displays OK or Error. This is the state of the position sensors.
Power Mode Active	-	Yes	The scan tool displays Yes or No. This is the state of the power mode.
Pump Motor Temp. Sensor	-	Varies	This displays Counts. This is the pump motor temperature measured in counts.
Pump Over Temperature Sensor	-	Normal	The scan tool displays Normal or Overtemp. This is the state of the pump temperature.
Rear Compartment Lid Pull Down Switch	-	Inactive	The scan tool displays Active or Inactive. This is the state of the rear compartment lid pull down switch.
Rear Tonneau Close Reference Position	-	Varies	This displays Counts. This is the close reference position of the rear tonneau measured in counts.
Rear Tonneau Open Reference Position	-	Varies	This displays Counts. This is the open reference position of the rear tonneau measured in counts.
Rear Tonneau Position Sensor	-	Varies	This displays Counts. This is the position of the rear tonneau measured in counts.
Rear Tonneau Status	-	Tonneau Closed	The scan tool displays Tonneau Open, Tonneau Closed or Mid. This is the state of the rear tonneau.
System Timer	-	OK	The scan tool displays OK or Expired. This is the state of the system timer.
System Voltage	-	OK	The scan tool displays OK or Low. This is the state of the system voltage.
Too Cold For Top Operation	-	No	The scan tool displays Yes or No. Yes is displayed if the temperature is too cold for top operation.
Top Closed Limit Switch	-	Off	The scan tool displays On or Off. This is the state of the top closed limit switch.
Top Control	-	Enabled	The scan tool displays Enabled or Inhibited. This is the state of the top control.
Top Control Switch	-	Idle	The scan tool displays Idle, Top Open, Top Closed or Invalid. This is the state of the top control switch.
Top Position Error	-	No	The scan tool displays Yes or No. Yes is displayed if there was a top position error.
Trunk Control	-	Enabled	The scan tool displays Enabled or Inhibited. This is the state of the trunk control.
Valet Status	-	Varies	The scan tool displays Active or Inactive. This is the state of the valet.
Valve 1-5 Command	-	Off	The scan tool displays On or Off. This is the state of the commanded corresponding valve.
Vehicle In Park	-	Yes	The scan tool displays Yes or No. Yes is displayed if the vehicle is in park.

Folding Top Module Scan Tool Output Controls

Output Control	Description
Valve 1 Command	The FTC module commands Valve 1 to energize or not. As the valve is energized, a click can be heard, activating the valve.
Valve 2 Command	The FTC module commands Valve 2 to energize or not. As the valve is energized, a click can be heard, activating the valve.
Valve 3 Command	The FTC module commands Valve 3 to energize or not. As the valve is energized, a click can be heard, activating the valve.
Valve 4 Command	The FTC module commands Valve 4 to energize or not. As the valve is energized, a click can be heard, activating the valve.
Valve 5 Command	The FTC module commands Valve 5 to energize or not. As the valve is energized, a click can be heard, activating the valve.
Pump Motor A Direction	The FTC module commands to operate in the A direction. The motor should operate in the requested direction.
Pump Motor B Direction	The FTC module commands to operate in the B direction. The motor should operate in the requested direction.