Common Specs & Procedures Index
SRX COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 159 lb ft (215 N.m) | ||
| Rear | 159 lb ft (215 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS L | ||
| Drive Belts | |||
| 2.8L & 3.0L | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Belt Routing | See illustration under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 2.8L | |||
| 3.0L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LF1) or ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LAU) | ||
| Water Pump R & I | |||
| 2.8L & 3.0L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 2.8L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (139 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LAU OR LBW) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LAU OR LBW) | ||
| 3.0L | |||
| Compression | No cylinder reading should be less than 140 psi (965 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LF1) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LF1) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Step 1 | 22 ft lb (30 N.m) | ||
| Final Step | + an additional 45 degrees | ||
| Fuel System | |||
| Pressure Specification | 2.8L 55-60 psi (380-410 kPa) 3.0L 55-62 psi (384-425 kPa) |
||
| Fuel Pressure Test Procedure | 2.8L See FUEL SYSTEM DIAGNOSIS (LAU EXCEPT CHINA)
. 3.0L See FUEL SYSTEM DIAGNOSIS (LF1 EXCEPT CHINA) . |
||
| Fuel Filter Location | Fuel filter is located on the fuel feed pipe, between the fuel pump and the fuel rail. Fuel sender strainers are located on fuel senders in fuel tank. See FUEL PUMP FLOW CONTROL MODULE REPLACEMENT . | ||
| Fuel Filter R & I | FUEL FILTER REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.8L & 3.0L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires | Engine has coil-on-plug ignition. | ||
| Spark Plug | |||
| 2.8L (Type AC 41-990) | |||
| Gap | 0.043 in (1.10 mm) | ||
| Torque | 21 lb ft (28 N.m) | ||
| 3.0L (Type GM 12571535) | |||
| Gap | 0.043 in (1.1 mm) | ||
| Torque | 13 lb ft (18 N.m) | ||
| Starting | |||
| Starter | STARTER REPLACEMENT (LAU) or STARTER REPLACEMENT (LF1) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LAU OR LBW) or FASTENER TIGHTENING SPECIFICATIONS (LF1) | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque (See Tightening Pattern under wheel and tire INSTALLATION PROCEDURE | 100 ft lb (140 N.m) | ||