Common Specs & Procedures Index
SRX COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front/Rear | 184 ft lb (250 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See illustration under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure is stamped on cap | ||
| Thermostat R & I | |||
| 2.8L & 3.0L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LF1) or ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LAU) |
||
| Water Pump R & I | |||
| 2.8L & 3.0L | See WATER PUMP REPLACEMENT Or AUXILIARY WATER PUMP REPLACEMENT (LAU) | ||
| Engine Mechanical | |||
| 2.8L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (139 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LAU) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LAU) | ||
| 3.0L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LF1) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LF1) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| A/T | First pass 22 ft lb (30 N.m) Final pass an additional 45 degrees |
||
| M/T | First pass 22 ft lb (30 N.m) Final pass an additional 75 degrees |
||
| Fuel System | |||
| Pressure Specification | 2.8L & 3.0L 297-400 kPa (43-58 psi) idling at operating temperature | ||
| Fuel Pressure Test Procedure | 2.8L CIRCUIT/SYSTEM VERIFICATION 3.0L CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | 2.8L on the fuel feed pipe, between the fuel pump and the fuel rail. 3.0L fuel filter is located in the primary fuel tank module. |
||
| Fuel Filter R & I | N/A | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.8L (Type N/A) | |||
| Gap | 0.043 in (1.1 mm) | ||
| Torque | 21 lb ft (28 N.m) | ||
| 3.0L (Type ) | |||
| Gap | 0.043 in (1.1 mm) | ||
| Torque | 13 lb ft (18 N.m) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 110 lb ft (150 N.m) See Wheel Nut Tightening Sequence Illustration under INSTALLATION PROCEDURE | ||