Common Specs & Procedures Index
STS COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 159 ft lb (215 N.m) | ||
| Rear | 159 ft lb (215 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS (JE5, JL9) OR For Heavy Duty see DISC BRAKE COMPONENT SPECIFICATIONS (J56) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See illustration under WATER PUMP AND GENERATOR BELT REPLACEMENT and/or AIR CONDITIONING COMPRESSOR AND POWER STEERING PUMP BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | No cylinder reading should be less than 965 kPa (140 psi). Lowest reading should not be less than 70 percent of highest reading. See ENGINE COMPRESSION TEST | ||
| Oil Pressure | Minimum @ Idle 10 psi (69 kPa) Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LLT) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| Automatic Transmission | first pass 22 ft lb (30 N.m) second pass additional 45 degrees |
||
| Fuel System | |||
| Pressure Specification (Ignition ON, engine OFF) | command fuel pump relay ON using scan tool 345-414 kPa (50-60 psi) |
||
| Fuel Pressure Test Procedure | See CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | In Line filter is located on fuel feed pipe, between fuel pump and fuel rail See illustration under FUEL FILTER REPLACEMENT |
||
| Fuel Filter R & I | FUEL FILTER REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 3.6L (Type N/A) | |||
| Gap | 0.043 in (1.1 mm) | ||
| Torque | 15 ft lb (20 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft lb (140 N.m) See Wheel tightening sequence illustration under wheel Installation Procedure | ||