LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2012 >> Escalade EXT >> Repair and Diagnosis >> External Pages >> Different car >> Section 54 (Engine Controls - Removal & Installation) >> Torque Specifications
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Torque Specifications

WARNING: This page is about a different car, the 2003 Pontiac Sunfire and 2003 Chevrolet Cavalier. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
CNG Fuel Inlet Fitting-To-Tank Valve 18 (24)
CNG Fuel Outlet Fitting-To-Tank Valve 20 (27)
CNG Fuel Tank Pressure Sensor 20 (27)
CNG Fuel Tank Strap Nut 35 (48)
CNG Tank Vent Fitting Between HPL Fill Line Port & Female Vent Hose Fitting 35 (48)
Fill Line 30 (41)
Fill Line-To-Union Fitting 27 (37)
Fill Valve Retaining Nut 30 (41)
Fuel Tank Retaining Strap Bolt 26 (35)
FTP Sensor 20 (27)
FTP Sensor Port Fitting 27 (37)
FTP Sensor Port Fitting CAP 35 (48)
HO2S 1 22 (30)
HO2S 2 30 (41)
HPL Fill Line Fitting 27 (37)
HPL Solenoid (1) 225 (305)
HPL Pressure Relief Device Line 27 (37)
HPL-To-HPR Fitting 18 (24)
HPR Mounting Nut 41 (55)
Ignition Control Module Retaining Screw 13 (1.5)
Ignition Control Module Cover Bolt 18 (10)
Knock Sensor Retaining Bolt 18 (24)
Low Pressure Lock-Off Mounting Bolt 9 (12)
LPL Fuel Inlet Elbow Fitting 18 (24)
LPR/LPL-To-Transaxle Mounting Studs 20 (28)
(2) Outlet Fitting Cap 27 (37)
Pressure Relief Device-To-HPL 27 (37)
Spare Tire Bracket Bolt 20 (27)
Starter Bolt 30 (41)
CNG Tank Strap Nut 35 (47)
INCH Lbs. (N.m) 
Accelerator Cable Bracket Nut 89 (10)
Air Cleaner Duct-To-Resonator Clamp 44 (5)
Air Cleaner Intake Duct Clamp 44 (5)
Battery Cable Clamp Bolt 133 (15)
CNG Fuel Tank Cover Bolts 54 (6)
CNG Low Pressure Lock-Off Regulator Bolt 108 (12)
CNG Low Pressure Lock-Off Solenoid Bracket Nut 108 (12)
Crankshaft Position Sensor Bolt/Nut 71 (8)
Cruise Control Cable Bracket 89 (10)
Engine Coolant Temperature Sensor 89 (10)
EVAP Canister Purge Valve Bracket Nut 71 (8)
EVAP Canister Retainer Bolt 89 (10)
Exhaust Shield Bolt 18 (2)
Exhaust Shield Nut 9 (1)
Fuel Hose Retainer Hold-Down Nut 106 (12)
Fuel Injector Control Module Mounting Bolts 106 (12)
Fuel Line Fitting-To-Fuel Rail 89 (10)
Fuel Pressure Regulator Bolt 89 (10)
Fuel Rail Attaching Bolt 89 (10)
Fuel Tank Pressure Sensor (1)
Hose Clamps 18 (2)
HPL Connector Stand-Offs 106 (12)
Idle Air Control Valve Screw 27 (3)
Ignition Coil Housing Retaining Bolt 89 (10)
Ignition Control Module-To-Housing Bolt 89 (10)
LPR & LPL Mounting Bolt 108 (12)
(2) Manual Vent Tool 106 (12)
Throttle Body Retaining Bolt 89 (10)
Throttle Position Sensor Screw 18 (2)
Union-To-HPL Fill Line 27 (37)
Upper Radiator Mounting Brackets Bolts 89 (10)
Hood Latch Support Bolts 80 (9)
Vent Boot Hose Clamp 18 (2)
(1) A nominal torque at zero degrees. You must compensate for the torque wrench and the HPL crowfoot offset. To obtain your dial reading, multiply torque wrench length in inches by 305. 18 inch torque wrench example: 18 X 305 = 5490. Add 3 to the length of torque wrench. 18 inch torque wrench example: 18 + 3 = 21. Divide the first value obtained by the second value obtained. The result indicates the amount of torque your wrench should tighten the HPL to. 18 inch torque wrench example: 5490 divided by 21 = 261.4. For an 18 inch long torque wrench tighten the HPL to 193 ft. lbs. (261.4 N.m).
(2) From CNG Take Venting Kit (J 42435)