Common Specs & Procedures Index
SRX - COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 250 N.m (184 lb ft) | ||
| Rear | 250 N.m (184 lb ft) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT REPLACEMENT | ||
| Drive Belt Routing | See figure under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped on Cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LFW, LFX) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LFW, LFX) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2,000 RPM - 138 kPa (20 psi) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LFW) ENGINE MECHANICAL SPECIFICATIONS (LFX) |
||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass - 30 N.m (22 lb ft) Final Pass - 45 Degrees |
||
| Fuel System | |||
| Pressure Specification | Ignition ON, Engine OFF, 345-690 kPa (50-100 psi) Engine Idling - 300-400 kPa (43-58 psi) See CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | (Except China) Fuel Filter is part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | FUEL PUMP FLOW CONTROL MODULE REPLACEMENT FUEL FILTER REPLACEMENT (CHINA) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | ELECTRONIC IGNITION SYSTEM DIAGNOSIS | ||
| Ignition Wires (Routing) | |||
| 3.6L | SPARK PLUG REPLACEMENT | ||
| Spark Plug | |||
| 3.6L For plug application, see parts catalog. | |||
| Gap | 1.1 mm (0.043 in) | ||
| Torque | 20 N.m (15 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 150 N.m (110 lb ft) For Tightening Sequence, please see the figure under INSTALLATION PROCEDURE |
||