Common Specs & Procedures Index
XTS COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | First Pass 150 N.m (111 lb ft) Second Pass loosen 45 degrees Final Pass 250 N.m (184 lb ft) |
||
| Rear | First Pass 150 N.m (111 lb ft) Second Pass loosen 45 degrees Final Pass 250 N.m (184 lb ft) |
||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) Or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the Figure Under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LFX) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LFX) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2,000 RPM - 138 kPa (20 psi) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LFX) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass - 30 N.m (22 lb. ft.) Final Pass - + 45 degrees |
||
| Fuel System | |||
| Pressure Specification | Ignition ON, Engine OFF - 345-690 kPa (50-100 psi) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (AWD) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | |||
| 3.6L | Coil On Plug | ||
| Spark Plug - For application, see parts catalog. | |||
| 3.6L | |||
| Gap | 0.95-1.10 mm (0.0375-0.0433 in) | ||
| Torque | 18 N.m (13 lb. ft.) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 150 N.m (111 lb ft) For Lug Nut Tightening Sequence, Please See the Figure Under TIRE AND WHEEL REMOVAL AND INSTALLATION (WITH J64) 5-Lug or TIRE AND WHEEL REMOVAL AND INSTALLATION (WITH J55) 6-Lug |
||