Common Specs & Procedures Index
CTS - SEDAN COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 250 N.m (184 lb ft.) | ||
| Rear | 270 N.m (199 lb ft.) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | Right Rear, Left Front, Left Rear, Right Front HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) Or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | NA | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | For 2.0L, See the figure under DRIVE BELT REPLACEMENT For 3.6L, See the figure under DRIVE BELT REPLACEMENT (LFX) or DRIVE BELT REPLACEMENT (LF3) |
||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 2.0L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LTG) | ||
| 3.6L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LFX, LF3) | ||
| Water Pump R & I | |||
| 2.0L | WATER PUMP REPLACEMENT (LTG) | ||
| 3.6L | WATER PUMP REPLACEMENT (LFX, LF3) | ||
| Engine Mechanical | |||
| 2.0L (LTG) | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 140-200 kPa (20-29 psi) @700 RPM 100°C | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS |
||
| Torque | FASTENER SPECIFICATIONS | ||
| 3.6L (LF3, LFX) | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 69 kPa at Idle (10 psig at Idle) 138 kPa at 2,000 engine RPM (20 psig at 2,000 engine RPM) Piston Cooling Jet Valve Pressure 1.7-2.3 bar (25-33 psi) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LF3) ENGINE MECHANICAL SPECIFICATIONS (LFX) |
||
| Torque | FASTENER SPECIFICATIONS (LF3) FASTENER SPECIFICATIONS (LFX) |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.0L | First Pass 20 N.m (15 lb ft) Second Pass 30 N.m (22 lb ft) Final Pass 40 Degrees |
||
| 3.6L | First Pass 30 N.m (22 lb ft) Final Pass 45 Degrees |
||
| Fuel System | |||
| Pressure Specification | 2.0L - Ignition ON 380 - 520 kPa (55-76 psi) Engine Idling - 300 - 400 kPa (43-58 psi) 3.6L - Ignition ON, Engine OFF 345 - 690 kPa (50-100 psi) |
||
| Fuel Pressure Test Procedure | 2.0L CIRCUIT/SYSTEM VERIFICATION 3.6L LFX CIRCUIT/SYSTEM VERIFICATION or LF3CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | 2.0L inside Fuel Tank Fuel Pump Module 3.6L - Next To Fuel Tank |
||
| Fuel Filter R & I | 2.0L FUEL TANK FUEL PUMP MODULE REPLACEMENT 3.6L FUEL FILTER REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2.0L & 3.6L coil on plug | ||
| Ignition Wires (Routing) | |||
| 2.0L & 3.6L | coil on plug | ||
| Spark Plug | |||
| 2.0L See parts catalog for part number. | |||
| Gap | 0.95-1.10 mm (0.0375-0.0433 in) | ||
| Torque | 20 N.m (15 lb ft) | ||
| 3.6L See parts catalog for part number. | |||
| Gap | LF3 0.90 mm (.035 in) LFX 0.95-1.1 mm (0.0375-0.0433 in) |
||
| Torque | 25 N.m (18 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 150 N.m (111 lb ft) For Wheel Nut Tightening Sequence, See Illustration Under INSTALLATION PROCEDURE |
||