Common Specs & Procedures Index

ATS COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		APPROXIMATE FLUID CAPACITIES
Torque		FASTENER SPECIFICATIONS
Axle Nut/Hub Nut Front
Tighten		250 N.m (184 lb. ft.)
Rear Wheel Drive Shaft Nut
Tighten Using Described Procedure		FASTENER SPECIFICATIONS
Battery		NA
Brakes
Bleeding Sequence		RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE)
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Charging
Generator		CHARGING SYSTEM TEST
Torque		FASTENER SPECIFICATIONS
Drive Belts
Adjustment		Non-Adjustable Serpentine Belt
Drive Belt Routing		See the figure under 2.0L, 2,5L DRIVE BELT REPLACEMENT Or 3.6L DRIVE BELT REPLACEMENT (LF4)DRIVE BELT REPLACEMENT (LGX)
Engine Cooling
General Service Specifications		N/A
	Radiator Cap Pressure	Pressure Stamped On Cap
	Thermostat R & I
	2.0L, 2.5L 3.6L	2.0L, 2.5L ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LGX) 3.6L ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LF4)
	Water Pump R & I
	2.0L 2.5L 3.6L	WATER PUMP REPLACEMENT (LTG)WATER PUMP REPLACEMENT (LF4)WATER PUMP REPLACEMENT (LGX)
Engine Mechanical
2.0L, 2.5L
	Compression	ENGINE COMPRESSION TEST
	Oil Pressure	2.0L Minimum - @700 RPM @100°C - 140-200 kPa (20-29 psi) 2.5L Minimum - @700 RPM @100°C - 154-220 kPa (22-32 psi)
	Overhaul	2.0L ENGINE MECHANICAL SPECIFICATIONS (LTG) 2.5L ENGINE MECHANICAL SPECIFICATIONS (LCV)
	Torque	2.0L FASTENER SPECIFICATIONS (LTG) 2.5L FASTENER SPECIFICATIONS (LCV)
3.6L
	Compression	ENGINE COMPRESSION TEST
	Oil pressure	3.6L Minimum @ Idle - 69 kPa (10 psi) 3.6L Minimum @ 2,000 RPM - 138 kPa (20 psi)
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (LF4) ENGINE MECHANICAL SPECIFICATIONS (LGX)
	Torque	FASTENER SPECIFICATIONS (LF4) FASTENER SPECIFICATIONS (LGX)
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque - 2.0L, 2.5L		First Pass - 30 N.m (22 lb ft) Final Pass - additional 80 degrees
Flywheel/Flex Plate/Drive Plate Torque - 3.6L		First Pass - 30 N.m (22 lb ft) Final Pass - Additional 45 degrees
Fuel System
Pressure Specification - 2.0L, 2.5L		Ignition ON, Engine OFF - 345-650 kPa (50-94 psi)
Pressure Specification - 3.6L		Ignition ON, Engine OFF - 345-690 kPa (50-100 psi)
	Fuel Pressure Test Procedure - 2.0L, 2.5L	CIRCUIT/SYSTEM VERIFICATION
	Fuel Pressure Test Procedure - 3.6L	LGX CIRCUIT/SYSTEM VERIFICATION LF4 CIRCUIT/SYSTEM VERIFICATION
	Fuel Filter Location - 2.0L, 2.5L	Fuel Filter is Part of the Primary Fuel Tank Fuel Pump Module
	Fuel Filter Location - 3.6L	Fuel Filter is Part of the Primary Fuel Tank Fuel Pump Module
	Fuel Filter R & I - 2.0L, 2.5L	See FUEL TANK FUEL PUMP MODULE REPLACEMENT
	Fuel Filter R & I - 3.6L	See FUEL TANK FUEL PUMP MODULE REPLACEMENT
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		Coil On Plug
Ignition Wires (Routing)
2.0L, 2.5L, 3.6L		Coil On Plug
Spark Plug
2.0L, 2.5L See Parts Catalog for Application
	Gap	0.95-1.10 mm (0.037-0.043 in )
	Torque	20 N.m (15 lb ft)
3.6L See Parts Catalog for Application
	Gap	0.95-01.10 mm (0.0375-0.0433 in )
	Torque	18 N.m (13 lb ft)
Starting
Starter		N/A
Torque		FASTENER SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		Non V Series 140 N.m (103 lb ft) V-Series Built on October 4th 2015 and Earlier 150 N.m (111 lb ft) V-Series Built on October 5th 2015 and Later 190 N.m (140 lb ft) For Tightening Sequence, Please see the appropriate Figure Under TIRE AND WHEEL REMOVAL AND INSTALLATION