LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2016 >> SRX Base >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Power Door Lock System And Release Systems >> Diagnostic Information and Procedures >> DTC B2495 or B24A0: Liftgate Latch Control Circuit/Power Liftgate Latch Release Motor Circuit >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Liftgate Release Inoperative

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the low reference circuit terminal 6 and ground.
    • If 10 Ω or greater 
    1. Disconnect the harness connector at the K39 Liftgate Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K39 Liftgate Control Module.
    • If less than 10 Ω 
  3. Connect the harness connector at the A23C Liftgate Latch Assembly.
  4. Disconnect the X3 harness connector at the K39 Liftgate Control Module. Ignition ON.
  5. Test for less than 1 V between the control circuit terminal 13 and ground.
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, test or replace the A23C Liftgate Latch Assembly.
    • If less than 1 V 
  6. Manually move the latch to cinched position.
  7. Briefly connect a 30 A fused jumper wire between the control circuit terminal 13 and 12 V.
  8. Verify the A23C Liftgate Latch Assembly performs the release function.
    • If the A23C Liftgate Latch Assembly does not release 
    1. Ignition OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly.
    2. Test for infinite resistance the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the A23C Liftgate Latch Assembly.
    • If the A23C Liftgate Latch Assembly releases 
  9. Replace the K39 Liftgate Control Module.

Liftgate Cinch Inoperative

  1. Ignition OFF, disconnect the X2 harness connector at the K39 Liftgate Control Module.
  2. Test for less than 1 V between the control circuit terminals listed below and ground:
    • Control circuit terminal 1 X2
    • Control circuit terminal 2 X2
    • If 1 V or greater 
    1. Ignition OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly. ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
    • If less than 1 V 
  3. Test for infinite resistance between the control circuit terminals listed below and ground:
    • Control circuit terminal 1 X2
    • Control circuit terminal 2 X2
    • If less than infinite resistance 
    1. Ignition OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the A23C Liftgate Latch Assembly.
    • If infinite resistance 
  4. Test for less than 10 Ω between the control circuit terminal 1 and the control circuit terminal 2.
    • If 10 Ω or greater 
    1. Ignition OFF, disconnect the harness connector at the A23C Liftgate Latch Assembly.
    2. Test for less than 2 Ω between the K39 Liftgate Control Module control circuit terminal 1 and the A23C Liftgate Latch Assembly control circuit terminal 7.
      • If 2 Ω or greater, repair the open/high resistance on the circuit.
    3. Test for less than 2 Ω between the K39 Liftgate Control Module control circuit terminal 2 and the A23C Liftgate Latch Assembly control circuit terminal 8.
      • If 2 Ω or greater, repair the open/high resistance on the circuit.
      • If less than 2 Ω, replace the A23C Liftgate Latch Assembly.
    • If less than 10 Ω 
  5. Replace the K39 Liftgate Control Module.
scientia non olet · About LEMON Manuals