Common Specs & Procedures Index
XTS COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | First Pass 150 N.m (111 lb ft) Second Pass loosen 45 degrees Final Pass 250 N.m (184 lb ft) |
||
| Rear | First Pass 150 N.m (111 lb ft) Second Pass loosen 45 degrees Final Pass 250 N.m (184 lb ft) |
||
| Battery | N/A | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) Or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the Figure Under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LFX, LF3) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LFX, LF3) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2,000 RPM - 138 kPa (20 psi) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LF3) ENGINE MECHANICAL SPECIFICATIONS (LFX) |
||
| Torque | FASTENER SPECIFICATIONS (LF3) FASTENER SPECIFICATIONS (LFX) |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass - 30 N.m (22 lb. ft.) Final Pass - + 45 degrees |
||
| Fuel System | |||
| Pressure Specification | Ignition ON, Engine OFF (Commanded With Scan Tool) - 345-690 kPa (50-100 psi) | ||
| Fuel Pressure Test Procedure | LF3 CIRCUIT/SYSTEM VERIFICATION LFX CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (AWD) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NT7/NU5 - FWD) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NU6 - FWD) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | |||
| 3.6L | Coil On Plug | ||
| Spark Plug - For application, see parts catalog. | |||
| 3.6L | |||
| Gap | LFX 0.95-1.10 mm (0.0375-0.0433 in) LF3 .90mm (.035 in) |
||
| Torque | 18 N.m (13 lb. ft.) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 150 N.m (111 ft lb) For Lug Nut Tightening Sequence, Please See the Figure Under TIRE AND WHEEL REMOVAL AND INSTALLATION (WITH J55) (WITH J55) or TIRE AND WHEEL REMOVAL AND INSTALLATION (WITH J64) (WITH J64) |
||