Test 3

Ignition/Vehicle & All vehicle systems» Off
NOTE: It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.
Disconnect the electrical connector: S79P Window Switch - Passenger
Test for less than 10 Ω between the test points: Ground circuit terminal 1 & Ground
- If 10 Ω or greater
1. Ground Connection» Disconnect
2. Test for less than 2 Ω between the test points: Ground circuit terminal 1 @ Component harness & Ground Connection
  - If 2 Ω or greater» Repair the open/high resistance in the circuit.
  - If less than 2 Ω» Repair the open/high resistance in the ground connection.
- If less than 10 Ω
Ignition » On / Vehicle » In Service Mode
Verify the scan tool parameter: Passenger Window Switch at Door=Inactive
- If not the specified state
1. Ignition/Vehicle» Off
2. Disconnect the electrical connector: M74P Window Motor - Passenger
3. Test for infinite resistance between the test points:
  - Signal circuit terminal 7 @ Component harness & Ground
  - Signal circuit terminal 8 @ Component harness & Ground
  - If less than infinite resistance» Repair the short to ground on the circuit.
  - If infinite resistance» Replace the component: M74P Window Motor - Passenger
- If the specified state
Momentarily connect a 3 A fused jumper wire between the test points: Signal circuit terminal 8 @ Component harness & Ground
Verify the scan tool parameter: Passenger Window Switch at Door=Up
- If not the specified state
1. Ignition/Vehicle» Off & Remove» Jumper wire(s)
2. Disconnect the electrical connector: M74P Window Motor - Passenger
3. Ignition» On / Vehicle» In Service Mode
4. Test for less than 1 V between the test points: Signal circuit terminal 8 @ Component harness & Ground
  - If 1 V or greater» Repair the short to voltage on the circuit.
  - If less than 1 V
5. Ignition/Vehicle» Off
6. Test for less than 2 Ω between the test points: Signal circuit terminal 8 @ Component harness & Terminal 3 @ M74P Window Motor - Passenger
  - If 2 Ω or greater» Repair the open/high resistance in the circuit.
  - If less than 2 Ω» Replace the component: M74P Window Motor - Passenger
- If the specified state
Momentarily connect a 3 A fused jumper wire between the test points: Signal circuit terminal 7 @ Component harness & Ground
Verify the scan tool parameter: Passenger Window Switch at Door=Down
- If not the specified state
1. Ignition/Vehicle» Off & Remove» Jumper wire(s)
2. Disconnect the electrical connector: M74P Window Motor - Passenger
3. Ignition» On / Vehicle» In Service Mode
4. Test for less than 1 V between the test points: Signal circuit terminal 7 @ Component harness & Ground
  - If 1 V or greater» Repair the short to voltage on the circuit.
  - If less than 1 V
5. Ignition/Vehicle » Off
6. Test for less than 2 Ω between the test points: Signal circuit terminal 8 @ Component harness & Terminal 3 @ M74P Window Motor - Passenger
  - If 2 Ω or greater» Repair the open/high resistance in the circuit.
  - If less than 2 Ω» Replace the component: M74P Window Motor - Passenger
- If the specified state
Test for greater than 10 V between the test points: Signal circuit terminal 6 @ Component harness & Ground
- If 10 V or less
1. Ignition/Vehicle » Off
2. Disconnect the electrical connector: M74P Window Motor - Passenger
3. Test for infinite resistance between the test points: Signal circuit terminal 6 @ Component harness & Ground
  - If less than infinite resistance» Repair the short to ground on the circuit.
  - If less than infinite resistance
1. Ignition/Vehicle» Off
2. Test for less than 2 Ω between the test points: Signal circuit terminal 6 @ Component harness & Signal circuit terminal 5 @ M74P Window Motor - Passenger
- If 2 Ω or greater» Repair the open/high resistance in the circuit.
- If less than 2 Ω» Replace the component: M74P Window Motor - Passenger
- If the specified state
Test or replace the component: S79P Window Switch - Passenger