LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2017 >> CT6 Plug-In >> Repair and Diagnosis >> Brakes >> Traction Control >> Antilock Brake System - Hybrid >> Repair Instructions >> Brake Pressure Modulator Valve Replacement >> Removal Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Removal Procedure

WARNING: Brake Fluid Irritant Warning
CAUTION: Brake Fluid Effects on Paint and Electrical Components Caution
CAUTION: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.
  1. Place the ignition switch in the OFF position.
  2. Engine Wiring Harness Fuse Block Bracket» Remove - Engine Wiring Harness Fuse Block Bracket Replacement
  3. Thoroughly clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any accumulated dirt and debris.
  4. Disconnect the EBCM electrical connector.
  5. Brake Pressure Modulator Valve Primary Brake Pipe Fitting (1)» Disconnect
    Fig 1: Brake Pressure Modulator Valve Primary Brake Pipe Fitting
    GM4476865Courtesy of GENERAL MOTORS COMPANY
  6. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.
  7. Brake Pressure Modulator Valve Secondary Brake Pipe Fitting (1)» Disconnect
    Fig 2: Brake Pressure Modulator Valve Secondary Brake Pipe Fitting
    GM4476873Courtesy of GENERAL MOTORS COMPANY
  8. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.
  9. Brake Pressure Modulator Valve Low Pressure Brake Pipe Fitting (1)» Disconnect
    Fig 3: Brake Pressure Modulator Valve Low Pressure Pipe Fitting
    GM4476876Courtesy of GENERAL MOTORS COMPANY
  10. Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.
  11. Brake Pipe Fitting (Left Front) (1)» Disconnect
    Fig 4: Brake Pipe Fitting (Left Front)
    GM4476881Courtesy of GENERAL MOTORS COMPANY
  12. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
  13. Brake Pipe Fitting (Right Front) (1)» Disconnect
    Fig 5: Brake Pipe Fitting (Right Front)
    GM4476887Courtesy of GENERAL MOTORS COMPANY
  14. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
  15. Brake Pipe Fitting (Left Rear) (1)» Disconnect
    Fig 6: Brake Pipe Fitting (Left Rear)
    GM4476892Courtesy of GENERAL MOTORS COMPANY
  16. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
  17. Brake Pipe Fitting (Right Rear) (1)» Disconnect
    Fig 7: Brake Pipe Fitting (Right Rear)
    GM4476897Courtesy of GENERAL MOTORS COMPANY
  18. Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.
  19. Brake Pressure Modulator Valve Bracket Nut (1)» Remove
    Fig 8: Brake Pressure Modulator Valve Bracket Nut
    GM4476904Courtesy of GENERAL MOTORS COMPANY
  20. Brake Pressure Modulator Valve Bracket Bolt (1)» Loosen
    Fig 9: Brake Pressure Modulator Valve Bracket Bolt
    GM4245825Courtesy of GENERAL MOTORS COMPANY
  21. Brake Pressure Modulator Valve Bracket Bolt (1)» Loosen
    Fig 10: Brake Pressure Modulator Valve Bracket Bolt
    GM4245826Courtesy of GENERAL MOTORS COMPANY
  22. Brake Pressure Modulator Valve Assembly (1)» Remove
    Fig 11: Brake Pressure Modulator Valve Assembly
    GM4476914Courtesy of GENERAL MOTORS COMPANY
scientia non olet · About LEMON Manuals