LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2017 >> Escalade ESV Base, RWD >> Repair and Diagnosis >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Object Detection System And Pedestrian Protection System - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> Lane Departure Warning System Malfunction (Chevrolet, GMC) >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Lane Departure Warning Switch Circuit Malfunction

  1. Ignition ON and all vehicle systems OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 8 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the ground circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify the scan tool Lane Departure Warning Switch Status parameter is Open.
    • If not Inactive 
    1. Ignition OFF, disconnect the harness connector at the B174W Frontview Camera - Windshield.
    2. Test for infinite resistance between the signal circuit terminal 10 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the B174W Frontview Camera - Windshield.
    • If Inactive 
  4. Install a 3 A fused jumper wire between the signal circuit terminal 10 and ground.
  5. Verify the scan tool Lane Departure Warning Switch Status parameter is Closed.
    • If not Closed 
    1. Ignition OFF, disconnect the harness connector at the B174W Frontview Camera - Windshield, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the B174W Frontview Camera - Windshield.
    • If Closed 
  6. Test or replace the S48A Multifunction Switch - Instrument Panel.

Lane Departure Warning Switch Indicator Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel, ignition ON.
  2. Verify a test lamp illuminates between the control circuit terminal 5 and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for less than 2 Ω in the control circuit end to end.
    • If the test lamp illuminates 
  3. Ignition OFF, connect the harness connector at the S48A Multifunction Switch - Instrument Panel. Disconnect the X1 harness connector at the B174W Frontview Camera - Windshield, ignition ON.
  4. Verify the lane departure warning switch indicator is not illuminated.
    • If the lane departure warning switch indicator is illuminated 
    1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel.
    2. Test for infinite resistance between the S48A Multifunction Switch - Instrument Panel control circuit terminal 6 and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • If infinite resistance, replace the S48A Multifunction Switch - Instrument Panel.
    • If the lane departure warning switch indicator is not illuminated 
  5. Connect a 3 A fused jumper wire between the control circuit terminal 4 and ground.
  6. Verify the lane departure warning switch indicator is illuminated.
    • If the lane departure warning switch indicator is not illuminated 
    1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the S48A Multifunction Switch - Instrument Panel.
    • If the lane departure warning switch indicator is illuminated 
  7. Replace the B174W Frontview Camera - Windshield.
scientia non olet · About LEMON Manuals