Common Specs & Procedures Index

ATS COMMON SPECS & PROCEDURES

SYSTEM		SPECIFICATION/PROCEDURE
Air Conditioning
General Service Specifications		SPECIFICATIONS
Torque		FASTENER SPECIFICATIONS
Wheel drive shaft nut
Front		250 N.m (184 lb. ft.)
Rear
250 N.m (184 lb. ft.)
Battery		BATTERY INSPECTION/TEST
Brakes
Bleeding Sequence		RIGHT REAR, LEFT FRONT, LEFT REAR, RIGHT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE)
Disc Brakes
	Service Specifications	SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Charging
Generator		GENERATOR REPLACEMENT (LTG) , GENERATOR REPLACEMENT (LGX) , GENERATOR REPLACEMENT (LF4)
Torque		FASTENER SPECIFICATIONS
Drive Belts
Adjustment		Non-Adjustable Serpentine Belt
Drive Belt Routing		See the figure under 2.0L DRIVE BELT REPLACEMENT , or 3.6L DRIVE BELT REPLACEMENT (LF4) , DRIVE BELT REPLACEMENT (LGX)
Engine Cooling
General Service Specifications		SPECIFICATIONS
	Radiator Cap Pressure	PRESSURE CAP TESTING
	Thermostat R & I
	ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LGX) ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LF4) ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LTG)
	Water Pump R & I
	WATER PUMP REPLACEMENT (LF4) WATER PUMP REPLACEMENT (LTG) WATER PUMP REPLACEMENT (LGX)
Engine Mechanical
2.0L
	Compression	ENGINE COMPRESSION TEST
	Oil Pressure	Minimum - @700 RPM @100°C - 140-200 kPa (20-29 psi)
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
3.6L
	Compression	ENGINE COMPRESSION TEST
	Oil pressure	Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2,000 RPM - 138 kPa (20 psi)
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (LF4) ENGINE MECHANICAL SPECIFICATIONS (LGX)
	Torque	FASTENER SPECIFICATIONS (LF4) FASTENER SPECIFICATIONS (LGX)
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flex Plate/Flywheel Torque A/T Flex Plate Torque - 2.0L		First Pass - 30 N.m (22 lb ft) Final Pass - additional 40 degrees
M/T Flywheel Torque - 2.0L		First Pass - 30 N.m (22 lb ft) Final Pass - additional 80 degrees
A/T Flex Plate Torque - 3.6L		First Pass - 30 N.m (22 lb ft) Final Pass - Additional 45 degrees
M/T Flywheel Torque - 3.6L		First Pass - 30 N. m (22 lb ft) Final Pass - additional 60 degrees
Fuel System
	Fuel Pressure Test Procedure - 2.0L	CIRCUIT/SYSTEM VERIFICATION
	Fuel Pressure Test Procedure - 3.6L	LF4 CIRCUIT/SYSTEM VERIFICATION LGX CIRCUIT/SYSTEM VERIFICATION
	Fuel Filter Location - 2.0L	Fuel Filter is Part of the Primary Fuel Tank Fuel Pump Module
	Fuel Filter Location - 3.6L	Fuel Filter is Part of the Primary Fuel Tank Fuel Pump Module
	Fuel Filter R & I - 2.0L	See FUEL TANK FUEL PUMP MODULE REPLACEMENT
	Fuel Filter R & I - 3.6L	See FUEL TANK FUEL PUMP MODULE REPLACEMENT
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		Coil On Plug
Ignition Wires (Routing)
Coil On Plug
Spark Plug
2.0L, See Parts Catalog for Application
	Gap	0.95-1.10 mm (0.037-0.043 in)
	Torque	20 N.m (15 lb ft)
3.6L See Parts Catalog for Application
	Gap	0.90 mm (0.035 in)
	Torque	18 N.m (13 lb ft)
Starting
Starter		STARTER REPLACEMENT (LGX) , STARTER REPLACEMENT (LTG) , STARTER REPLACEMENT (LF4 - MANUAL TRANSMISSION) , STARTER REPLACEMENT (LF4 - AUTOMATIC TRANSMISSION)
Torque		FASTENER SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		150 N.m (111 lb ft) For Tightening Sequence, Please see the appropriate Figure Under INSTALLATION PROCEDURE (Non-V series) , INSTALLATION PROCEDURE (V series)