Common Specs & Procedures Index
XT4 COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Drive Shaft Nut | |||
| Front Wheel Drive Shaft Nut | First Pass: 150 N.m (111 lb ft) Second Pass: Loosen 45 Degrees Final Pass: 250 N.m (185 lb ft) |
||
| Rear Wheel Drive Shaft Nut | First Pass: 150N.m (111 lb ft) Second Pass: Loosen 45 Degrees Final Pass: 250 N.m (185 lb ft) |
||
| Battery | BATTERY INSPECTION/TEST | ||
| Brakes | |||
| Bleeding Sequence | LEFT REAR, LEFT FRONT, RIGHT FRONT, RIGHT REAR See HYDRAULIC BRAKE SYSTEM BLEEDING . |
||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR REPLACEMENT | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the Figure Under DRIVE BELT SYSTEM DESCRIPTION | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | RADIATOR SURGE TANK CAP TESTING | ||
| Thermostat R & I | |||
| ENGINE COOLANT FLOW CONTROL VALVE REPLACEMENT | |||
| Water Pump R & I | |||
| ELECTRIC ENGINE COOLANT PUMP REPLACEMENT | |||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | Engine @ 1500 RPM - 125-185 kPa (18.13-26.83 psi) - 20° C (68° F) | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Engine Flywheel Bolt Torque | First Pass: 20 N.m (15 lb ft) Final Pass: + 70 degrees |
||
| Fuel System | |||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (AWD) , FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | |||
| Coil On Plug | |||
| Spark Plug - For application, see parts catalog. | |||
| Gap | 0.70 mm-0.80 mm (0.028-0.031 in) | ||
| Torque | 17 N.m (13 lb. ft.) | ||
| Starting | |||
| Starter | STARTER REPLACEMENT (FWD) , STARTER REPLACEMENT (AWD) | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 190 N.m (140 ft lb) For Lug Nut Tightening Sequence, Please See the Figure Under INSTALLATION PROCEDURE |
||