Common Specs & Procedures Index
ESCALADE, ESCALADE ESV, SUBURBAN, TAHOE, YUKON & YUKON XL - COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications Automatic - Fastener Specifications |
||
| Axle Nut/Hub Nut | |||
| Front | 255 N.m (188 lb ft) | ||
| Battery | Battery Inspection/Test , or Battery Electrical Drain/Parasitic Load Test , or Battery Description and Operation | ||
| Brakes | |||
| Bleeding Sequence | Hydraulic Brake System Bleeding (Manual) or Hydraulic Brake System Bleeding (Pressure) | ||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Generator Replacement | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See graphic at "Identifying Accessory Drive Belt Routing" under: Drive Belt Replacement - Accessory | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| Engine Coolant Thermostat Housing Replacement | |||
| Water Pump R & I | |||
| 5.3L & 6.2L | Water Pump Replacement | ||
| Engine Mechanical | |||
| 5.3L & 6.2L | |||
| Compression | Engine Compression Test | ||
| Oil Pressure - Minimum Hot | @ 1000 RPM - 152 kPa (22 psig) @ 2000 RPM - 207 kPa (30 psig) @ 3000 RPM - 228 kPa (33 psig) |
||
| Overhaul | Engine Mechanical Specifications (L83) or Engine Mechanical Specifications (L86) | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 5.3L & 6.2L Automatic - First Pass - 15 N.m (11 lb ft) Second Pass - 30 N.m (22 lb ft) Final Pass - 45 Degrees |
||
| Fuel System | |||
| Pressure Specification | 5.3L & 6.2L - Ignition ON, engine OFF, command the Fuel Pump Enable ON with a scan tool: 320 to 608 kPa (46 to 88 psi) | ||
| Fuel Pressure Test Procedure | 5.3L & 6.2L - Circuit/System Verification | ||
| Fuel Filter Location | Inside the fuel tank. Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | 5.3L & 6.2L Fuel Tank Fuel Pump Module Replacement (SWB) or Fuel Tank Fuel Pump Module Replacement (LWB) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | 5.3L & 6.2L Firing Order & Cylinder Identification |
||
| Ignition Wires (Resistance) | 5.3L & 6.2L - 170 to 220 ohms per 25.4 mm (1.0 in), Individual Ignition Coils | ||
| Ignition Wires (Routing) | |||
| 5.3L & 6.2L | Coil on Plug | ||
| Spark Plug | |||
| 5.3L & 6.2L - Type - See parts catalog | |||
| Gap | 5.3L & 6.2L - 0.95-1.10 mm (0.037-0.043 in) | ||
| Torque | 5.3L & 6.2L - 20 N.m (15 lb ft) | ||
| Starting | |||
| Starter | Starter Replacement | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 190 N.m (140 lb ft) See graphic at "Identifying Wheel Nut Tightening Sequence" under: Tire and Wheel Removal and Installation |
||