Common Specs & Procedures Index
XT5 - COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities (R-134a) , or Approximate Fluid Capacities (R-1234yf) | ||
| Torque | Fastener Specifications | ||
| Wheel Drive Shaft Nut | |||
| Front Wheel Drive Shaft Nut | First Pass: 330 N.m (244 lb ft) Second Pass: Loosen 45 Degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | Battery Inspection/Test | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See Hydraulic Brake System Bleeding (Manual without JEO) Or Hydraulic Brake System Bleeding (Pressure without JEO) Or Hydraulic Brake System Bleeding (Pressure with JEO) . |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Charging System Test | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the Figure Under Accessory Drive Primary Belt Replacement (2.0L LSY) Or Drive Belt Replacement (3.6L LGX) | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 2.0L | Engine Coolant Thermostat Housing Inlet Pipe Removal , or Engine Coolant Thermostat Housing Inlet Pipe Installation | ||
| 3.6L | Engine Coolant Thermostat Housing Removal , or Engine Coolant Thermostat Housing Installation | ||
| Water Pump R & I | |||
| 2.0L | Electric Water Pump Replacement | ||
| 3.6L | Water Pump Replacement (LGX) , or Auxiliary Water Pump Replacement (LGX) | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | Engine Compression Test | ||
| Oil Pressure | @ 1500 RPM 100°C - 199.95 kPa (29 psi) | ||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| 3.6L | |||
| Compression | Engine Compression Test | ||
| Oil Pressure | Minimum @ Idle - 69 kPa (10 psi) Minimum @ 2, 000 RPM - 136 kPa (20 psi) |
||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Engine Flywheel Bolt Torque | 2.0L - N/A 3.6L - 67 N.m (49 lb ft) |
||
| Fuel System | |||
| Pressure Specification | 2.0L - Ignition ON, Engine OFF (Commanded With Scan Tool) - 320 to 608 kPa (46 to 88 psi) 3.6L - Ignition ON, Engine OFF (Commanded With Scan Tool) - 345 to 650 kPa (50 to 94 psi) |
||
| Fuel Pressure Test Procedure | 2.0L - Circuit/System Verification 3.6L - Circuit/System Verification |
||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | 2.0L - Fuel Tank Fuel Pump Module Replacement (FWD)
or Fuel Tank Fuel Pump Module Replacement (AWD) 3.6L - Fuel Tank Fuel Pump Module Replacement (FWD) or Fuel Tank Fuel Pump Module Replacement (AWD) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | |||
| 2.0L | Coil On Plug | ||
| 3.6L | Coil On Plug | ||
| Spark Plug - For application, see parts catalog. | |||
| 2.0L | |||
| Gap | 0.70 - 0.80 mm (0.028 - 0.031 in | ||
| Torque | 17 N.m (13 lb ft) | ||
| 3.6L | |||
| Gap | 0.90 mm (.035 in) | ||
| Torque | 18 N.m (13 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 190 N.m (140 ft lb) For Lug Nut Tightening Sequence, Please See the Figure Under Installation Procedure |
||